- 您现在的位置：买卖IC网 > PDF目录69108 > PRM48BF480T400A00 8.33 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, DMA24 PDF资料下载
参数资料
| 型号： | PRM48BF480T400A00 |
| 元件分类： | 稳压器 |
| 英文描述： | 8.33 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, DMA24 |
| 封装： | ROHS COMPLIANT PACKAGE-24 |
| 文件页数： | 7/22页 |
| 文件大小： | 1097K |
| 代理商： | PRM48BF480T400A00 |
Rev. 1.1
12 / 2010
Page 15 of 22
PRM48BF480T400A00
(Formerly VIP0001TFJ)
VI CHIP CORP. (A VICOR COMPANY) 25 FRONTAGE RD. ANDOVER, MA 01810 800-735-6200
10.0
PRODUCT DETAILS AND DESIGN GUIDELINES
10.1
Control pins description and characteristics
Control node (PR) is the input to the control node which
determines the powertrain timing and ultimately the
module output power (Figure 21).
An internal 0.5mA
current sink is always active. The bi-directional buffer
between PR and the control node has two states.
In
normal operation, PR will be above the 0.79V switching
threshold, and will drive the control node through the
buffer. An internal 7.4V clamp determines the maximum
output power that can be requested of the modulator.
When PR falls below 0.79 V, the converter will stop
switching. An internal circuit clamps the modulator input
control node to 0.79 V, and a buffer will source up to 2.5
mA out of the pin at that clamp level. For this reason, the
output impedance of the amplifier driving PR must be
taken into account. A rail-to-rail operational amplifier with
low output impedance is always recommended.
The powertrain small signal (plant) response consists of a
single pole determined by the load resistance, the
powertrain equivalent output resistance, and the total
output capacitance (internal and external to the module).
Both the modulator gain and the equivalent output
resistance vary as a function of line, load and output
voltage, as shown in Figures 17, 18 and 19. As the load
increases, the powertrain pole moves to higher frequency.
As a result, the closed loop crossover frequency will be the
highest at full load and lowest at minimum load. Figure 25
shows a reference AC small-signal model.
Current feedback (IF) is the input for the module output
overcurrent protection and current limit features (see
functional block diagram in section 4.0).
A voltage
proportional to the powertrain output current must be
applied to IF in order for overcurrent protection to operate
properly.
If the IF voltage exceeds the IF pin’s overcurrent
protection threshold, the powertrain will stop switching. If
the IF voltage falls below the overcurrent protection
threshold within TBLANK time, then the powertrain will
immediately resumes switching. Otherwise a fault is
latched.
The current limit threshold for the IF pin is set lower than
the protection threshold. When the IF pin average voltage
exceeds the current limit threshold, an internal integrator
will activate a clamp amplifier which overrides the
modulator input maximum level. This causes the
powertrain to maintain a constant output current.
The bandwidth of this current limit integrator is significantly
slower than that of the PR control node input. Therefore
this current limit can not be used in lieu of properly
compensating the (external) PR control loop to avoid
exceeding maximum current or power ratings for the
device.
If the IF pin is not driven, it must be resistively terminated
to SG. A 1k
resistor to SG is recommended in this case.
Figure 25 – PRM48BF480T400A00 AC small signal model
相关PDF资料 |
PDF描述 |
|---|---|
| PS200-I/P | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP20 |
| PS200-I/SS | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO20 |
| PS200-I/SO | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO20 |
| PS21997-4A | AC MOTOR CONTROLLER, DMA25 |
| PS21997-4 | AC MOTOR CONTROLLER, DMA25 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PRM48BF480T400B00 | 功能描述:REGULATOR PRM 48V OUT 400W SMD 制造商:vicor corporation 系列:VI Chip? PRM? 包装:散装 零件状态:有效 类型:预稳模块 输出数:1 电压 - 输入（最小值）:38V 电压 - 输入（最大值）:55V 电压 - 输出 1:48V 电压 - 输出 2:- 电压 - 输出 3:- 电流 - 输出（最大值）:11A 功率（W） - 制造系列:400W 电压 - 隔离:- 应用:ITE（商业） 特性:OCP，OTP，OVP，SCP，UVLO 安装类型:表面贴装 封装/外壳:模块 大小/尺寸:1.28" 长 x 0.87" 宽 x 0.26" 高（32.5mm x 22.0mm x 6.7mm） 工作温度:-40°C ~ 125°C 效率:97% 功率（W） - 最大值:400W 标准包装:40 |
| PRM48BF480T500A00 | 制造商:Vicor Corporation 功能描述:REGULATOR PRM 48V 10.42A 500W |
| PRM48BF480T600A00 | 功能描述:REGULATOR PRM 48V OUT 600W SMD 制造商:vicor corporation 系列:VI Chip? PRM? 包装:散装 零件状态:有效 类型:预稳模块 输出数:1 电压 - 输入（最小值）:38V 电压 - 输入（最大值）:55V 电压 - 输出 1:48V 电压 - 输出 2:- 电压 - 输出 3:- 电流 - 输出（最大值）:12.5A 功率（W） - 制造系列:600W 电压 - 隔离:- 应用:ITE（商业） 特性:OCP，OTP，OVP，SCP，UVLO 安装类型:表面贴装 封装/外壳:模块 大小/尺寸:1.28" 长 x 0.87" 宽 x 0.26" 高（32.5mm x 22.0mm x 6.7mm） 工作温度:-40°C ~ 125°C 效率:97.6% 功率（W） - 最大值:600W 标准包装:40 |
| PRM48BH480M250A00 | 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:PRMa?￠ Regulator |
| PRM48BH480T200A00 | 功能描述:HALF-CHIP PRM REGULATOR 48V 200W RoHS:是 类别:电源 - 板载 >> DC DC 转换器（分解式） 系列:V-I Chip™, PRM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块 输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V） 应用:商用 特点:具有远程开/关功能和 UVLO 安装类型:通孔 封装/外壳:模块 尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm） 包装:托盘 工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g） |
发布紧急采购，3分钟左右您将得到回复。