- 您现在的位置：买卖IC网 > PDF目录378075 > PSD813F2V-12J (意法半导体) Flash In-System Programmable ISP Peripherals For 8-bit MCUs PDF资料下载
参数资料
| 型号： | PSD813F2V-12J |
| 厂商： | 意法半导体 |
| 英文描述： | Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
| 中文描述： | Flash在系统可编程ISP的外设的8位微控制器 |
| 文件页数： | 72/110页 |
| 文件大小： | 1685K |
| 代理商： | PSD813F2V-12J |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页当前第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页
PSD813F1
72/110
JTAG Extensions
TSTAT and TERR are two JTAG extension signals
enabled by an
“
ISC_ENABLE
”
command received
over the four standard JTAG pins (TMS, TCK, TDI,
and TDO). They are used to speed programming
and erase functions by indicating status on PSD
pins instead of having to scan the status out seri-
ally using the standard JTAG channel.
TERR will indicate if an error has occurred when
erasing a sector or programming a byte in Flash
memory. This signal will go Low (active) when an
error condition occurs, and stay Low until an
“
ISC_CLEAR
”
command is executed or a chip re-
set pulse is received after an
“
ISC-DISABLE
”
com-
mand. TERR does not apply to EEPROM.
TSTAT behaves the same as the Ready/Busy sig-
nal described in the section entitled
Ready/Busy
Pin (PC3), page 18
. TSTAT will be High when the
PSD device is in READ mode (Flash memory and
EEPROM contents can be read). TSTAT will be
Low when Flash memory programming or erase
cycles are in progress, and also when data is be-
ing written to EEPROM.
TSTAT and TERR can be configured as open-
drain type signals during an
“
ISC_ENABLE
”
com-
mand. This facilitates a wired-OR connection of
TSTAT signals from several PSD devices and a
wired-OR connection of TERR signals from those
same devices. This is useful when several PSD
devices are
“
chained
”
together in a JTAG environ-
ment.
Security, Flash memory and EEPROM
Protection
When the security bit is set, the device cannot be
read on a device programmer or through the JTAG
Port. When using the JTAG Port, only a full chip
erase command is allowed. All other program/
erase/verify commands are blocked. Full chip
erase returns the part to a non-secured blank
state. The Security Bit can be set in PSDsoft Ex-
press Configuration.
All Flash Memory and EEPROM sectors can indi-
vidually be sector protected against erasures. The
sector protect bits can be set in PSDsoft Express
Configuration.
Table 34. JTAG Port Signals
INITIAL DELIVERY STATE
When delivered from ST, the PSD device has all
bits in the memory and PLDs set to '1.' The PSD
Configuration Register bits are set to '0.' The code,
configuration, and PLD logic are loaded using the
programming procedure. Information for program-
ming the device is available directly from ST.
Please contact your local sales representative.
Table 35. JTAG Enable Register
Note: The state of Reset (RESET) does not interrupt (or prevent) JTAG operations if the JTAG signals are dedicated by an NVM Configura-
tion bit (via PSDsoft Express). However, Reset (RESET) prevents or interrupts JTAG operations if the JTAG enable register is used
to enable the JTAG signals.
Port C Pin
JTAG Signals
Description
PC0
TMS
Mode Select
PC1
TCK
Clock
PC3
TSTAT
Status
PC4
TERR
Error Flag
PC5
TDI
Serial Data In
PC6
TDO
Serial Data Out
Bit 0
JTAG_Enable
0 = off JTAG port is disabled.
1 = on JTAG port is enabled.
Bit 1
X
0
Not used, and should be set to zero.
Bit 2
X
0
Not used, and should be set to zero.
Bit 3
X
0
Not used, and should be set to zero.
Bit 4
X
0
Not used, and should be set to zero.
Bit 5
X
0
Not used, and should be set to zero.
Bit 6
X
0
Not used, and should be set to zero.
Bit 7
X
0
Not used, and should be set to zero.
相关PDF资料 |
PDF描述 |
|---|---|
| PSD813F1A-12J | Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V |
| PSD813F1A-12JI | Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V |
| PSD813F1A-12JT | Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V |
| PSD813F4-12 | Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V |
| PSD813F4-15 | Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PSD813F2V-12J1T | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash in-system programmable (ISP) peripherals for 8-bit MCUs, 3.3 V |
| PSD813F2V-12JI | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
| PSD813F2V-12JIT | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
| PSD813F2V-12JT | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
| PSD813F2V-12M | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
发布紧急采购，3分钟左右您将得到回复。