- 您现在的位置：买卖IC网 > PDF目录378075 > PSD813F3V-12 (意法半导体) Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V PDF资料下载
参数资料
| 型号： | PSD813F3V-12 |
| 厂商： | 意法半导体 |
| 英文描述： | Flash In-System Programmable (ISP) Peripherals for 8-bit MCUs, 5V |
| 中文描述： | Flash在系统可编程（ISP）的周边8位MCU，5V的 |
| 文件页数： | 21/110页 |
| 文件大小： | 1685K |
| 代理商： | PSD813F3V-12 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页当前第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页
21/110
PSD813F1
INSTRUCTIONS
An instruction is defined as a sequence of specific
operations. Each received byte is sequentially de-
coded by the PSD and not executed as a standard
write operation. The instruction is executed when
the correct number of bytes are properly received
and the time between two consecutive bytes is
shorter than the time-out value. Some instructions
are structured to include READ operations after
the initial WRITE operations.
The sequencing of any instruction must be fol-
lowed exactly. Any invalid combination of instruc-
tion bytes or time-out between two consecutive
bytes while addressing Flash memory will reset
the device logic into READ mode (Flash memory
reads like a ROM device). An invalid combination
or time-out while addressing the EEPROM block
will cause the offending byte to be interpreted as a
single operation.
The PSD supports these instructions (see
Table
8., page 20
):
Flash memory:
Erase memory by chip or sector
Suspend or resume sector erase
Program a Byte
Reset to READ mode
Read Flash Identifier value
Read Sector Protection Status
EEPROM:
Write data to OTP Row
Read data from OTP Row
Power down memory
Enable Software Data Protect (SDP)
Disable SDP
Return from read OTP Row read mode or
power down mode.
I
I
I
I
I
I
I
I
I
I
I
I
These
8., page 20
. For efficient decoding of the instruc-
tions, the first two bytes of an instruction are the
coded cycles and are followed by a command byte
or confirmation byte. The coded cycles consist of
writing the data AAh to address X555h during the
first cycle and data 55h to address XAAAh during
the second cycle. Address lines A15-A12 are don
’
t
cares during the instruction WRITE cycles. How-
ever, the appropriate sector select signal (FSi or
EESi) must be selected.
Power-down Instruction and Power-up Mode
EEPROM Power Down Instruction.
The
PROM can enter power down mode with the help
of the EEPROM power down instruction (see
Ta-
ble 8., page 20
). Once the EEPROM power down
instruction is decoded, the EEPROM memory can-
not be accessed unless a Return instruction (also
in
Table 8., page 20
) is decoded. Alternately, this
power down mode will automatically occur when
the APD circuit is triggered (see section entitled
Automatic Power-down (APD) Unit and Power-
down Mode, page 65
). Therefore, this instruction
is not required if the APD circuit is used.
Power-up Mode.
The PSD internal logic is reset
upon power-up to the READ mode. Any write op-
eration to the EEPROM is inhibited during the first
5ms following power-up. The FSi and EESi select
signals, along with the write strobe signal, must be
in the false state during power-up for maximum se-
curity of the data contents and to remove the pos-
sibility of a byte being written on the first edge of a
write strobe signal. Any write cycle initiation is
locked when V
CC
is below V
LKO
.
instructions
are
detailed
in
Table
EE-
相关PDF资料 |
PDF描述 |
|---|---|
| PSD8132V70JT | Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
| PSD8132V90JT | Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
| PSD8133V12JT | Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
| PSD8133V12MIT | Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
| PSD8133V12MT | Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PSD813F3V-12J | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
| PSD813F3V-12JI | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
| PSD813F3V-12JIT | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
| PSD813F3V-12JT | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
| PSD813F3V-12M | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Flash In-System Programmable ISP Peripherals For 8-bit MCUs |
发布紧急采购，3分钟左右您将得到回复。