- 您现在的位置：买卖IC网 > PDF目录69251 > PTB48510BAH (TEXAS INSTRUMENTS INC) 2-OUTPUT 72 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PTB48510BAH |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 电源模块 |
| 英文描述： | 2-OUTPUT 72 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | DIP-8 |
| 文件页数： | 3/17页 |
| 文件大小： | 544K |
| 代理商： | PTB48510BAH |
www.ti.com
CONFIGURING THE PTB4850x and PTB4851x DC/DC CONVERTERS FOR DSL APPLICATIONS
SWITCHING FREQUENCY SYNCHRONIZATION
POWER-UP SEQUENCING
SLTS219F – FEBRUARY 2004 – REVISED MARCH 2007
Table 1. Adjustment Range and Formula Parameters
PARAMETERS
PTB4851xA
PTB4851xB
PTB48510C
VO(nom) (V)
5
12
15
Va(min) (V)
3.5
6.5
7.2
Va(max) (V)
5.5
13.4
16.7
Vr (V)
2.495
Rn (k)
7.5
18.2
22.1
Rs (k)
9.09
16.9
NOTES:
1. A 0.05 W rated resistor may be used. The tolerance should be 1%, with a temperature stability of 100
ppm/
°C or better. Place the resistor in either the R
1 or (R2) location, as close to the converter as possible.
2. Never connect capacitors to the Vo Adj pin. Capacitance added to this pin can affect the stability of the
regulated output.
3. The overvoltage protection (PTB48511x) is nominally set to 25% above the original output voltage
set-point. Increasing the magnitude of the output voltages reduces the margin between the output voltage
and the overvoltage (OV) protection threshold. This could make the module more sensitive to OV faults, as a
result of random noise and load transients.
Note: An OV fault is a latched condition that shuts down the converter's outputs. The fault can be cleared by
cycling the Enable pin, or by momentarily removing input power to the module.
When operated as a pair, the PTB4850x and PTB4851x converters are specifically designed to provide all the
required supply voltages for powering xDSL chipsets. The PTB4850x produces two logic voltages. They include
a 3.3-V source for logic and I/O, and a low-voltage for powering a digital signal processor core. The PTB4851x
produces a balanced pair of complementary supply voltages that is required for the xDSL transceiver ICs. When
used together in these types of applications, the PTB4850x and PTB4851x may be configured for power-up
sequencing, and also synchronized to a common switch conversion frequency. Figure 19 shows the required
cross-connects between the two converters to enable these two features.
Unsynchronized, the difference in switch frequency introduces a beat frequency into the input and output AC
ripple components from the converters. The beat frequency can vary considerably with any slight variation in
either converter’s switch frequency. This results in a variable and undefined frequency spectrum for the ripple
waveforms, which would normally require separate filters at the input of each converter. When the switch
frequency of the converters are synchronized, the ripple components are constrained to the fundamental and
higher. This simplifies the design of the output filters, and allows a common filter to be specified for the treatment
of input ripple.
The desired power-up sequence for the AC7 supply voltages requires that the two logic-level voltages from the
PTB4850x converter rise to regulation prior to the two complementary voltages that power the transceiver ICs.
This sequence cannot be assured if the PTB4850x and PTB4851x are allowed to power up independently,
especially if the 48-V input voltage rises relatively slowly. To ensure the desired power-up sequence, the EN Out
pin of the PTB4850x is directly connected to the activelow Enable input of the PTB4851x (see Figure 19). This
allows the PTB4850x to momentarily hold off the outputs from the PTB4851x until the logic-level voltages have
risen first. Figure 19 shows the power-up waveforms of all four supply voltages from the schematic of Figure 19.
Copyright 2004–2007, Texas Instruments Incorporated
11
相关PDF资料 |
PDF描述 |
|---|---|
| PTB48510CAS | 2-OUTPUT 66 W DC-DC REG PWR SUPPLY MODULE |
| PTB48520WAH | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTB48520WAS | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTB48520WAZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTB48560AAS | 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PTB48510BAS | 功能描述:DC/DC转换器 72W+/-12V Dual Comp Outp DC/DC Converter RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PTB48510BAZ | 功能描述:DC/DC转换器 72W+/-12V Dual Comp Outp DC/DC Converter RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PTB48510C | 制造商:TI 制造商全称:Texas Instruments 功能描述:Dual Complementary-Output DC/DC Converter for DSL |
| PTB48510CAH | 功能描述:DC/DC转换器 66W+/- 5V Dual Comp Outp DC/DC Converter RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PTB48510CAS | 功能描述:DC/DC转换器 66W+/- 5V Dual Comp Outp DC/DC Converter RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。