参数资料
型号: PTFL04BC471Q2N34B0
厂商: Murata Electronics North America
文件页数: 99/105页
文件大小: 0K
描述: THERMISTOR
标准包装: 100
系列: Posistor®
在 25°C 时的电阻(欧姆): 470
工作温度: -10°C ~ 120°C
安装类型: 通孔
封装/外壳: 圆盘形,5.0mm 直径 x 4.0mm W
供应商设备封装: *
包装: 散装
! Note ? Please read rating and ! CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
? This catalog has only typical speci?cations. Therefore, please approve our product speci?cations or transact the approval sheet for product speci?cations before ordering.
R90E.pdf
Mar.4,2014
! Caution/Notice
Continued from the preceding page.
(2) Adhesive Application and Curing
(a) If insufficient adhesive is applied, or if the adhesive
is not sufficiently hardened, this product may have a
loose contact with the land, during flow soldering.
(b) Too low viscosity of adhesive causes this product to
slip on the board, after mounting.
Allowable Flow Soldering Temp. and Time
270
260
250
240
230
220
210
(3) Allowable Soldering Temperature and Time
(a) Solder within the temperature and time
combinations, indicated by the slanted lines in the
following graphs.
(b) Excessive soldering conditions may cause
dissolution of metallization or deterioration of
solder-wetting on the external electrode.
(c) In the case of repeated soldering, the accumulated
soldering time should be within the range shown in
the figures below. (For example, Reflow peak
temperature: 260°C, twice –> The accumulated
soldering time at 260°C is within 30sec.)
Allowable Reflow Soldering Temp. and Time
280
270
260
250
240
230
220
200
0
10 20
Time (sec.)
30
210
0 10 20 30 40 50 60 70 80 90 100 110
Time (sec.)
(4) Recommendable Temperature Profile for Soldering
(a) Insufficient preheating may cause a crack on the
ceramic body. The difference between preheating
temperature and maximum temperature in the profile
should be 100°C.
(b) Rapid cooling by dipping in solvent or by other
means is not recommended.
Flow Soldering Conditions
Reflow Soldering Conditions
Preheating (in air)
Soldering
Gradual cooling
(in air)
Preheating (in air)
Soldering
Gradual cooling
(in air)
200
100
0
250°C
200
100
0
250°C
1 to 2 min.
*3 sec.
1 to 2 min.
*20 sec.
Preheating: 150±10°C, 1-2 minutes.
Soldering: 250°C, 3 sec.
* In the case of repeated soldering, the accumulated soldering
time should be within the range shown in "(3) Allowable
Soldering Temperature and Time."
Preheating: 150±10°C, 1-2 minutes.
Soldering: 250°C, 20 sec.
* In the case of repeated soldering, the accumulated soldering
time should be within the range shown in "(3) Allowable
Soldering Temperature and Time."
(5) There may be a risk of unexpected failures
(tombstone, insufficient solder-wetting, etc.) in the
mounting process caused by mounting conditions.
Please make sure that this product is correctly mounted
under the specified mounting conditions.
97
相关PDF资料
PDF描述
PTFL04BC222Q2N34B0 THERMISTOR
PTFL04BB471Q2N34B0 THERMISTOR
PTFL04BB222Q2N51B0 THERMISTOR
PTFL04BB222Q2N34B0 THERMISTOR
PTFL04BD222Q2N51A0 THERMISTOR
相关代理商/技术参数
参数描述
PTFL04BD222Q2N34B0 功能描述:热敏电阻 - PTC 2200ohm PTC Thermistor RoHS:否 制造商:Vishay 电阻:1.5 kOhms 容差:1 % 端接类型:Radial 系列:TFPTL 工作温度范围:- 55 C to + 70 C
PTFL04BD222Q2N51A0 功能描述:热敏电阻 - PTC 2200ohm PTC Thermistor RoHS:否 制造商:Vishay 电阻:1.5 kOhms 容差:1 % 端接类型:Radial 系列:TFPTL 工作温度范围:- 55 C to + 70 C
PTFL04BD471Q2N34B0 功能描述:热敏电阻 - PTC 470ohm PTC Thermistor RoHS:否 制造商:Vishay 电阻:1.5 kOhms 容差:1 % 端接类型:Radial 系列:TFPTL 工作温度范围:- 55 C to + 70 C
PTFL04BE222Q2N34B0 功能描述:热敏电阻 - PTC 2200ohm PTC Thermistor RoHS:否 制造商:Vishay 电阻:1.5 kOhms 容差:1 % 端接类型:Radial 系列:TFPTL 工作温度范围:- 55 C to + 70 C
PTFL04BE471Q2N34B0 功能描述:热敏电阻 - PTC 470ohm PTC Thermistor RoHS:否 制造商:Vishay 电阻:1.5 kOhms 容差:1 % 端接类型:Radial 系列:TFPTL 工作温度范围:- 55 C to + 70 C