- 您现在的位置：买卖IC网 > PDF目录69255 > PTH12020WAST (TEXAS INSTRUMENTS INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | PTH12020WAST |
| 厂商： | TEXAS INSTRUMENTS INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封装： | DIP-10 |
| 文件页数： | 22/27页 |
| 文件大小： | 930K |
| 代理商： | PTH12020WAST |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页
ELECTRICAL CHARACTERISTICS
SLTS208I – MAY 2003 – REVISED MARCH 2009 ............................................................................................................................................................. www.ti.com
TA = 25°C, VI =12 V, VO = 1.8 V, CI = 560 F, CO = 0 F, and Io = Iomax (unless otherwise noted)
PTH12020L
PARAMETER
TEST CONDITIONS
UNIT
MIN
TYP
MAX
60°C, 200 LFM airflow
0
18(1)
IO
Output current
A
25°C, natural convection
0
18(1)
VI
Input voltage range
Over Io range
10.8
13.2
V
Votol
Set-point voltage tolerance
±2 (2)
%Vo
ΔRegtemp
Temperature variation
–40C <TA < 85°C
±0.5
%Vo
ΔRegline
Line regulation
Over VI range
±5
mV
ΔRegload
Load regulation
Over Io range
±5
mV
ΔRegtot
Total output variation
Includes set-point, line, load, –40°C
≤ TA ≤ 85°C
3 (2)
%Vo
ΔVadj
Output voltage adjust range
Over VI range
0.8
1.8
V
RSET = 130 , Vo = 1.8 V
89%
RSET = 3.57 k, Vo = 1.5 V
87%
η
Efficiency
IO = 12 A
RSET = 12.1 k, Vo = 1.2 V
85%
RSET = 32.4 k, Vo = 1.0 V
83%
RSET = open cct., Vo = 0.8 V
80%
Vr
Vo ripple (pk-pk)
20 MHz bandwidth
1
%Vo
Io trip
Over-current threshold
Reset, followed by auto-recovery
30
A
ttr
Recovery time
70
Sec
1 A/
s load step, 50 to
Transient response
100% Iomax,Cout = 330 F
ΔVtr
Vo over/undershoot
70
mV
ΔVomargin
Margin up/down adjust
±5%
IIL margin
Margin input current (pins 9 /10)
Pin to GND
–8(3)
A
IIL track
Track input current (pin 8)
Pin to GND
–0.13(3)
mA
dVtrack/dt
Track slew rate capability
Cout ≤ Cout(max)
1
V/ms
VI increasing
9.7
10.4
UVLO
Undervoltage lockout
V
VI decreasing
8.8
9.2
VIH
Input high voltage, Referenced to GND
Open(4)
V
VIL
Inhibit control (pin 3)
Input low voltage, Referenced to GND
–0.2
0.5
IIL
Input low current, Pin 3 to GND
0.24
mA
II
Input standby current
Inhibit (pin 3) to GND, Track (pin 8) open
5
mA
s
Switching frequency
Over VI and Io ranges
200
250
300
kHz
CI
External input capacitance
560(5)
F
Non-ceramic
0
330 (6)
9900 (7)
Capacitance value
F
CO
External output capacitance
Ceramic
0
300
Equivalent series resistance (non-ceramic)
4(8)
m
MTBF
Reliability
Per Bellcore TR-332, 50% stress, TA = 40°C, ground benign
5.3
106 Hrs
(1)
See SOA curves or consult factory for appropriate derating.
(2)
The set-point voltage tolerance is affected by the tolerance and stability of RSET. The stated limit is unconditionally met if RSET has a
tolerance of 1%, with 100 ppm/°C or better temperature stability.
(3)
A small low-leakage (<100 nA) MOSFET is recommended to control this pin. The open-circuit voltage is less than 1 Vdc.
(4)
This control pin is pulled up to an internal supply voltage. If this input is left open-circuit the module will operate when input power is
applied. A small low-leakage (<100 nA) MOSFET or open-drain/collector voltage supervisor IC is recommended for control. Do not place
an external pull-up on this pin. For further information, consult the related application note.
(5)
A 560
F electrolytic input capacitor is required for proper operation. The capacitor must be rated for a minimum of 800 mA rms of ripple
current.
(6)
An external output capacitor is not required for basic operation. Adding 330
F of distributed capacitance at the load will improve the
transient response.
(7)
This is the calculated maximum. The minimum ESR limitation will often result in a lower value. When controlling the Track pin using a
voltage supervisor, the maximum output capacitance is reduced to 6600
F. Consult the application notes for further guidance.
(8)
This is the typical ESR for all the electrolytic (non-ceramic) output capacitance. Use 7 m
as the minimum when using max-ESR values
to calculate.
4
Copyright 2003–2009, Texas Instruments Incorporated
Product Folder Link(s) :PTH12020W/L
相关PDF资料 |
PDF描述 |
|---|---|
| PTH12020LAZ | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH12050LAZT | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH12050WAH | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH12050LAST | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PTH12050WAS | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PTH12020WAZ | 功能描述:DC/DC转换器 ADJ 1.2-5.5V 18A Surface-Mount RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PTH12020WAZT | 功能描述:DC/DC转换器 10.8-13.2Vin 5.5V18A 1.495" x0.870"x0.354 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| PTH12030 | 制造商:EMERSON-NETWORKPOWER 制造商全称:Emerson Network Power 功能描述:DC-DC CONVERTERS |
| PTH12030L | 制造商:TI 制造商全称:Texas Instruments 功能描述:26-A, 12-V INPUT NON-ISOLATED WIDE-OUTPUT ADJUST POWER MODULE |
| PTH12030LAD | 功能描述:DC/DC转换器 10.2-13.8Vin 1.8V26A 1.370" x1.120"x0.354 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。