参数资料
型号: PTV05010WAH
厂商: TEXAS INSTRUMENTS INC
元件分类: 电源模块
英文描述: 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
封装: SIP-8
文件页数: 3/19页
文件大小: 462K
代理商: PTV05010WAH
www.ti.com
Overcurrent Protection (OCP)
Output On/Off Inhibit
VI
L
O
A
D
1=Inhibit
GND
VO
Q1
BSS138
RSET
C1
C3
C2
PTV05010W
VI
VO
GND
Inhibit
V Adj
O
Track
SLTS242A – FEBRUARY 2005 – REVISED OCTOBER 2005
From the moment a valid input voltage is applied, the soft-start control introduces a short time delay (typically
8ms to 15ms) before allowing the output voltage to rise. The output then progressively rises to the module
set-point voltage. Figure 8 shows the soft-start power-up characteristic of the PTV05010W, operating from a 5-V
input bus and configured for a 1.8-V output. The waveforms were measured with a 5-A resistive load and the
Auto-Track feature disabled. The initial rise in input current when the input voltage first starts to rise is the charge
current drawn by the input capacitors. Power up is complete within 25 ms.
For protection against load faults, the modules incorporate output overcurrent protection. Applying a load that
exceeds the overcurrent threshold causes the regulated output to shut down. Following shutdown, a module
periodically attempts to recover by initiating a soft-start power up. This is described as a hiccup mode of
operation, whereby the module continues in the cycle of successive shutdown and power up until the load fault is
removed. During this period, the average current flowing into the fault is significantly reduced. Once the fault is
removed, the module automatically recovers and returns to normal operation.
For applications requiring output voltage on/off control, the modules incorporate an output Inhibit control pin. The
inhibit feature can be used wherever there is a requirement for the output voltage from the regulator to be turned
off.
The power modules function normally when the Inhibit input is left open-circuit, providing a regulated output
whenever a valid source voltage is connected to VI with respect to GND.
Figure 9 shows the typical application of the inhibit function. Note the discrete transistor (Q1). The Inhibit input
has its own internal pullup (see footnotes to electrical characteristics table). The input is not compatible with TTL
logic devices. An open-collector (or open-drain) discrete transistor is recommended for control.
Figure 9. On/Off Inhibit Application Circuit
Turning Q1 on applies a low voltage to the Inhibit control and disables the output of the module. If Q1 is then
turned off, the module executes a soft-start power-up sequence. A regulated output voltage is produced within
25ms. Figure 10 shows the typical rise in both the output voltage and input current, following the turnoff of Q1.
The turnoff of Q1 corresponds to the rise in the waveform, Q1 VDS. The waveforms were measured with a 5-A
constant current load.
Copyright 2005, Texas Instruments Incorporated
11
Product Folder Link(s) :PTV05010W
相关PDF资料
PDF描述
PTV08T250WAH 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
PTV08T250WAD 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
PTV12010WAD 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
PTV12010WAH 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
PVX003A0X43-SRZ 1-OUTPUT DC-DC REG PWR SUPPLY MODULE
相关代理商/技术参数
参数描述
PTV05020 制造商:EMERSON-NETWORKPOWER 制造商全称:Emerson Network Power 功能描述:DC-DC CONVERTERS
PTV05020W 制造商:TI 制造商全称:Texas Instruments 功能描述:18-A, 5-V INPUT NONISOLATED WIDE-OUTPUT ADJUST SIP MODULE
PTV05020WAD 功能描述:DC/DC转换器 64.8W 0.8-3.6V 18A RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压(标称): 输出端数量:1 输出电压(通道 1):3.3 V 输出电流(通道 1):600 mA 输出电压(通道 2): 输出电流(通道 2): 安装风格:SMD/SMT 封装 / 箱体尺寸:
PTV05020WAH 功能描述:DC/DC转换器 18A 5VInput Non-Iso Wide-Adj SIP Module RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压(标称): 输出端数量:1 输出电压(通道 1):3.3 V 输出电流(通道 1):600 mA 输出电压(通道 2): 输出电流(通道 2): 安装风格:SMD/SMT 封装 / 箱体尺寸:
PTV07RW25-187SA-S2 制造商:Amphenol Corporation 功能描述:TV 187C 187#23 SKT RECP HD