参数资料
型号: Q83C154DCXXX-25
厂商: ATMEL CORP
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQFP44
封装: CERAMIC, QFP-44
文件页数: 22/242页
文件大小: 3080K
代理商: Q83C154DCXXX-25
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页第189页第190页第191页第192页第193页第194页第195页第196页第197页第198页第199页第200页第201页第202页第203页第204页第205页第206页第207页第208页第209页第210页第211页第212页第213页第214页第215页第216页第217页第218页第219页第220页第221页第222页第223页第224页第225页第226页第227页第228页第229页第230页第231页第232页第233页第234页第235页第236页第237页第238页第239页第240页第241页第242页
118
2588F–AVR–06/2013
ATtiny261/461/861
Table 12-20 shows the COM1D1:0 bit functionality when the PWM1D and WGM11:10 bits are
set to Phase and Frequency Correct PWM Mode.
Bit 1 – FOC1D: Force Output Compare Match 1D
The FOC1D bit is only active when the PWM1D bit specify a non-PWM mode.
Writing a logical one to this bit forces a change in the Waveform Output (OCW1D) and the Out-
put Compare pin (OC1D) according to the values already set in COM1D1 and COM1D0. If
COM1D1 and COM1D0 written in the same cycle as FOC1D, the new settings will be used. The
Force Output Compare bit can be used to change the output pin value regardless of the timer
value. The automatic action programmed in COM1D1 and COM1D0 takes place as if a compare
match had occurred, but no interrupt is generated. The FOC1D bit is always read as zero.
Bit 0 – PWM1D: Pulse Width Modulator D Enable
When set (one) this bit enables PWM mode based on comparator OCR1D.
12.12.4
TCCR1D – Timer/Counter1 Control Register D
Bit 7 – FPIE1: Fault Protection Interrupt Enable
Setting this bit (to one) enables the Fault Protection Interrupt.
Bit 6 – FPEN1: Fault Protection Mode Enable
Setting this bit (to one) activates the Fault Protection Mode.
Bit 5 – FPNC1: Fault Protection Noise Canceler
Setting this bit activates the Fault Protection Noise Canceler. When the noise canceler is acti-
vated, the input from the Fault Protection Pin (INT0) is filtered. The filter function requires four
successive equal valued samples of the INT0 pin for changing its output. The Fault Protection is
therefore delayed by four Oscillator cycles when the noise canceler is enabled.
Bit 4 – FPES1: Fault Protection Edge Select
This bit selects which edge on the Fault Protection pin (INT0) is used to trigger a fault event.
When the FPES1 bit is written to zero, a falling (negative) edge is used as trigger, and when the
FPES1 bit is written to one, a rising (positive) edge will trigger the fault.
Table 12-20. Compare Output Mode, Phase and Frequency Correct PWM Mode
COM1D1:0
OCW1D Behaviour
OC1D Pin
00
Normal port operation.
Disconnected
01
Cleared on Compare Match when up-counting.
Set on Compare Match when down-counting.
Connected
10
Cleared on Compare Match when up-counting.
Set on Compare Match when down-counting.
Connected
Disconnected
11
Set on Compare Match when up-counting.
Cleared on Compare Match when down-counting.
Connected
Disconnected
Bit
76543210
FPIE1
FPEN1
FPNC1
FPES1
FPAC1
FPF1
WGM11
WGM10
TCCR1D
Read/Write
R/W
Initial value
00000000
相关PDF资料
PDF描述
Q83C154DTXXX-30D 8-BIT, MROM, 30 MHz, MICROCONTROLLER, CQFP44
Q80C32-30SHXXX:RD 8-BIT, 30 MHz, MICROCONTROLLER, CQFP44
Q80C32-36:R 8-BIT, 36 MHz, MICROCONTROLLER, CQFP44
Q80C32-44SHXXX:RD 8-BIT, 44 MHz, MICROCONTROLLER, CQFP44
Q80C32E-25:RD 8-BIT, 25 MHz, MICROCONTROLLER, CQFP44
相关代理商/技术参数
参数描述
Q-840 制造商:Qualtek Electronics Corporation 功能描述:Nema St Blade Twist Lock
Q-842 制造商:Qualtek Electronics Corporation 功能描述:NEMA TWIST-LOCK 制造商:Qualtek Electronics Corporation 功能描述:Nema St Blade Twist Lock
Q-844 制造商:Qualtek Electronics Corporation 功能描述:NEMA TWIST-LOCK 制造商:Qualtek Electronics Corporation 功能描述:Nema St Blade Twist Lock
Q-846 制造商:Qualtek Electronics Corporation 功能描述:NEMA TWIST-LOCK 制造商:Qualtek Electronics Corporation 功能描述:Nema St Blade Twist Lock
Q-848 制造商:Qualtek Electronics Corporation 功能描述:NEMA TWIST-LOCK 制造商:Qualtek Electronics Corporation 功能描述:Nema St Blade Twist Lock