参数资料
| 型号： | QT60240-ATG |
| 厂商： | Atmel |
| 文件页数： | 22/26页 |
| 文件大小： | 0K |
| 描述： | IC TOUCH SENSOR 24KEY 32-TQFP |
| 标准包装： | 3,000 |
| 系列： | QMatrix™ |
| 类型： | 电容性 |
| 输入数/键： | 24 键 |
| 分辨率（位）： | 10 b |
| 评估套件： | 可供 |
| 数据接口： | I²C，串行，SPI? |
| 电压基准： | 外部 |
| 电源电压： | 1.8V，3.3V，5V |
| 电流 - 电源： | 4.6mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-TQFP |
| 供应商设备封装： | 32-TQFP |
| 包装： | 带卷 (TR) |
| 其它名称： | QT60240-ATG-ND QT60240-ATGTR |
QmBtn software is available free of charge on Quantum’s
website www.qprox.com.
The signal swing from the smallest finger touch should
preferably exceed 8 counts, with 12 being a reasonable
target. The signal threshold setting (NTHR) should be set to a
value guaranteed to be less than the signal swing caused by
the smallest touch.
Increasing the burst length (BL) parameter will increase the
signal strengths as will increasing the sampling resistor (Rs)
values.
2.7 Matrix Series Resistors
The X and Y matrix scan lines can use series resistors
(referred to as Rx and Ry respectively) for improved EMC
performance (Figure 2.7, page 9).
X drive lines require Rx in most cases to reduce edge rates
and thus reduce RF emissions. Typical values range from
1K
to 20K.
Y lines need Ry to reduce EMC susceptibility problems and in
some extreme cases, ESD. Typical Y values are about 1K
.
Y resistors act to reduce noise susceptibility problems by
forming a natural low-pass filter with the Cs capacitors.
It is essential that the Rx and Ry resistors and Cs capacitors
be placed very close to the chip. Placing these parts more
than a few millimeters away opens the circuit up to high
frequency interference problems (above 20MHz) as the trace
lengths between the components and the chip start to act as
RF antennae.
The upper limits of Rx and Ry are reached when the signal
level and hence key sensitivity are clearly reduced. The limits
of Rx and Ry will depend on key geometry and stray
capacitance, and thus an oscilloscope is required to
determine optimum values of both.
Dwell time is the duration in which charge coupled from X to
Y is captured (Figure 2.4, page 4). Increasing Rx values will
cause the leading edge of the X pulses to increasingly roll off,
causing the loss of captured charge (and hence loss of signal
strength) from the keys.
The dwell time of these parts is fixed at 500ns. If the X pulses
have not settled within 500ns, key gain will be reduced; if this
happens, either the stray capacitance on the X line(s) should
be reduced (by a layout change, for example by reducing X
line exposure to nearby ground planes or traces), or, the Rx
resistor needs to be reduced in value (or a combination of
both approaches).
lQ
5
QT60240-ISG R8.06/0906
Figure 2.5 Probing X-Drive
Waveforms With a Coin
Figure 2.6 Recommended Key Structure
‘T’ should ideally be similar to the complete thickness the fields
need to penetrate to the touch surface. Smaller dimensions will also
work but will give less signal strength. If in doubt, make the pattern
coarser. The lower figure shows a simpler structure used for
compact key layouts, for example for mobile phones. A layout with a
common X drive and three receive electrodes is depicted.
Y1
Y0
X0
Y2
相关PDF资料 |
PDF描述 |
|---|---|
| MS27472T24B35SA | CONN RCPT 128POS WALL MNT W/SCKT |
| VI-JWN-MX-F4 | CONVERTER MOD DC/DC 18.5V 75W |
| VI-200-MX-F1 | CONVERTER MOD DC/DC 5V 75W |
| VI-B5Y-IU-B1 | CONVERTER MOD DC/DC 3.3V 132W |
| VI-JWN-MX-F1 | CONVERTER MOD DC/DC 18.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| QT60240-ATG SL924 | 制造商:Atmel Corporation 功能描述:INTEGRATED-CIRCUIT 制造商:Atmel 功能描述:INTEGRATED-CIRCUIT |
| QT60240-ATG-SL924 | 功能描述:接口 - 专用 Integrated Circuit RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| QT60240-ISG | 功能描述:接口 - 专用 1.8 - 5.5V 24 Chan QMatrix RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| QT60240-ISG QS130 | 功能描述:SENSOR IC MTRX TOUCH24KEY 32-QFN RoHS:是 类别:集成电路 (IC) >> 数据采集 - 触摸屏控制器 系列:QMatrix™ 标准包装:96 系列:- 类型:- 触摸面板接口:- 输入数/键:- 分辨率（位）:- 评估套件:* 数据接口:- 数据速率/采样率 (SPS，BPS):- 电压基准:- 电源电压:- 电流 - 电源:- 工作温度:- 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| QT60240-ISG-QS130 | 功能描述:接口 - 专用 1.8 - 5.5V 24 Chan QMatrix RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
发布紧急采购，3分钟左右您将得到回复。