- 您现在的位置：买卖IC网 > PDF目录299818 > R0633YS10D (WESTCODE SEMICONDUCTORS LTD) 1269 A, 1000 V, SCR PDF资料下载
参数资料
| 型号： | R0633YS10D |
| 厂商： | WESTCODE SEMICONDUCTORS LTD |
| 元件分类： | 晶闸管 |
| 英文描述： | 1269 A, 1000 V, SCR |
| 封装： | 101A335, 3 PIN |
| 文件页数： | 8/12页 |
| 文件大小： | 349K |
| 代理商： | R0633YS10D |
WESTCODE Positive development in power electronics
R0663YS10x to R0633YS12x
Data Sheet. Types R0633YS10x to R0633YS12x Issue 2
Page 5 of 12
June, 2001
The total dissipation is now given by:
f
E
W
(original)
(TOT)
+
=
12.2 Determination without Measurement
In circumstances where it is not possible to measure voltage and current conditions, or for design
purposes, the additional losses E in joules may be estimated as follows.
Let E be the value of energy per reverse cycle in joules (curves in Figure 9).
Let f be the operating frequency in Hz
()
(
)
()
f
R
E
T
th
original
SINK
new
SINK
=
Where TSINK (new) is the required maximum heat sink temperature and
TSINK (original) is the heat sink temperature given with the frequency ratings.
A suitable R-C snubber network is connected across the thyristor to restrict the transient reverse voltage
to a peak value (Vrm) of 67% of the maximum grade. If a different grade is being used or Vrm is other than
67% of Grade, the reverse loss may be approximated by a pro rata adjustment of the maximum value
obtained from the curves.
NOTE 1- Reverse Recovery Loss by Measurement
This thyristor has a low reverse recovered charge and peak reverse recovery current. When measuring
the charge care must be taken to ensure that:
(a) a.c. coupled devices such as current transformers are not affected by prior passage of high
amplitude forward current.
(b) A suitable, polarised, clipping circuit must be connected to the input of the measuring oscilloscope
to avoid overloading the internal amplifiers by the relatively high amplitude forward current signal
(c) Measurement of reverse recovery waveform should be carried out with an appropriate critically
damped snubber, connected across diode anode to cathode. The formula used for the calculation
of this snubber is shown below:
dt
di
S
r
C
V
R
= 4
2
Where: Vr = Commutating source voltage
CS = Snubber capacitance
R
= Snubber resistance
13.0 Gate Drive
The recommended pulse gate drive is 30V, 15
with a short-circuit current rise time of not more than
0.5s. This gate drive must be applied when using the full di/dt capability of the device.
The duration of pulse may need to be configured with respect to the application but should be no shorter
than 20s, otherwise an increase in pulse current could be needed to supply the resulting increase in
charge to trigger.
相关PDF资料 |
PDF描述 |
|---|---|
| R0633YS10E | 1269 A, 1000 V, SCR |
| R0633YS10F | 1269 A, 1000 V, SCR |
| R0809LS10D | 1691 A, 1000 V, SCR |
| R0830LS12E | 1713 A, 1200 V, SCR |
| R0830LS12F | 1713 A, 1200 V, SCR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| R065821230 | 制造商:Bosch Rexroth 功能描述:Compact Ball Bushing CR 0658 12mm 制造商:BOSCH POWER TOOLS 功能描述:COMP BALL BUSH 0658 12MM |
| R065821240 | 制造商:Bosch Rexroth 功能描述:Compact Ball Bushing 0658 12mm |
| R065821630 | 制造商:Bosch Rexroth 功能描述:Compact Ball Bushing CR 0658 16mm |
| R065821640 | 制造商:Bosch Rexroth 功能描述:Compact Ball Bushing 0658 16mm |
| R065822030 | 制造商:Bosch Rexroth 功能描述:Compact Ball Bushing CR 0658 20mm |
发布紧急采购，3分钟左右您将得到回复。