- 您现在的位置：买卖IC网 > PDF目录4507 > R1EX25032ATA00A#S0 (Renesas Electronics America)IC EEPROM 32K 5MHZ 8TSSOP PDF资料下载
参数资料
| 型号： | R1EX25032ATA00A#S0 |
| 厂商： | Renesas Electronics America |
| 文件页数： | 20/24页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 32K 5MHZ 8TSSOP |
| 标准包装： | 1 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 32K (4K x 8) |
| 速度： | 3MHz，5MHz |
| 接口： | SPI 串行 |
| 电源电压： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 标准包装 |
| 其它名称： | R1EX25032ATA00A#S0DKR |
R1EX25032Axx00A/R1EX25064Axx00A
Hold Condition
The hold ( HOLD ) signal is used to pause any serial communications with the device without resetting the clocking
sequence.
During the hold condition, the serial data output (Q) is high impedance, and serial data input (D) and serial clock (C)
are don’t care.
To enter the hold condition, the device must be selected, with chip select ( S ) low.
Normally, the device is kept selected, for the whole duration of the hold condition. Deselecting the device while it is in
the hold condition, has the effect of resetting the state of the device, and this mechanism can be used if it is required to
reset any processes that had been in progress.
The hold condition starts when the hold ( HOLD ) signal is driven low at the same time as serial clock (C) already being
low (as shown in the following figure).
The hold condition ends when the hold ( HOLD ) signal is driven high at the same time as serial clock (C) already being
low.
The following figure also shows what happens if the rising and falling edges are not timed to coincide with serial clock
(C) being low.
Hold Condition Activation
HOLD status
HOLD status
C
HOLD
Notes
Data Protection at V CC On/Off
When V CC is turned on or off, noise on S inputs generated by external circuits (CPU, etc) may act as a trigger and turn
the EEPROM to unintentional program mode. To prevent this unintentional programming, this EEPROM have a power
on reset function. Be careful of the notices described below in order for the power on reset function to operate
correctly.
? S should be fixed to V CC during V CC on/off. Low to high or high to low transition during V CC on/off may
cause the trigger for the unintentional programming.
? V CC should be turned on/off after the EEPROM is placed in a standby state.
? V CC should be turned on from the ground level (V SS ) in order for the EEPROM not to enter the unintentional
programming mode.
? V CC turn on speed should be slower than 10 μ s/V.
? When WRSR or WRITE instruction is executed before V CC turns off, V CC should be turned off after waiting
write cycle time (t W ).
REJ03C0358-0002.Rev.0.02 Jan.14.2009
page 18 of 20
相关PDF资料 |
PDF描述 |
|---|---|
| EPF6024AQC208-3 | IC FLEX 6000 FPGA 24K 208-PQFP |
| R1EX25032ASA00A#S0 | IC EEPROM 32K 5MHZ 8SOP |
| A40MX02-2PL44 | IC FPGA MX SGL CHIP 3K 44-PLCC |
| HMM44DRYN | CONN EDGECARD 88POS DIP .156 SLD |
| HSM44DRYH | CONN EDGECARD 88POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| R1EX25032ATA00G | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Serial Peripheral Interface 32k EEPROM 64k EEPROM |
| R1EX25032ATA00I | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Serial Peripheral Interface Electrically Erasable and Programmable Read Only Memory |
| R1EX25032ATA00I#S0 | 制造商:Renesas Electronics Corporation 功能描述:SERIAL EEPROM 32K, SPI, TSSOP8, I-GRADE - Tape and Reel 制造商:Renesas Electronics Corporation 功能描述:IC EEPROM 32KBIT 5MHZ 8TSSOP 制造商:Renesas Electronics Corporation 功能描述:SPI 32KB EEPROM |
| R1EX25064ASA00A | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Serial Peripheral Interface Electrically Erasable and Programmable Read Only Memory |
| R1EX25064ASA00A#S0 | 功能描述:IC EEPROM 64K 5MHZ 8SOP RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:1 系列:- 格式 - 存储器:闪存 存储器类型:闪存 - NAND 存储容量:4G（256M x 16） 速度:- 接口:并联 电源电压:2.7 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP I 包装:Digi-Reel® 其它名称:557-1461-6 |
发布紧急采购，3分钟左右您将得到回复。