参数资料
型号: R5F2L3ACCDFA
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100
封装: 14 X 20 MM, 0.65 MM PITCH, PLASTIC, QFP-100
文件页数: 27/74页
文件大小: 959K
代理商: R5F2L3ACCDFA
34
2588F–AVR–06/2013
ATtiny261/461/861
Bits 6:4 – Res: Reserved Bits
These bits are reserved and will always read as zero.
Bits 3:0 – CLKPS3:0: Clock Prescaler Select Bits 3 - 0
These bits define the division factor between the selected clock source and the internal system
clock. These bits can be written run-time to vary the clock frequency to suit the application
requirements. As the divider divides the master clock input to the MCU, the speed of all synchro-
nous peripherals is reduced when a division factor is used. The division factors are given in
To avoid unintentional changes of clock frequency, a special write procedure must be followed
to change the CLKPS bits:
1.
Write the Clock Prescaler Change Enable (CLKPCE) bit to one and all other bits in
CLKPR to zero.
2.
Within four cycles, write the desired value to CLKPS while writing a zero to CLKPCE.
Interrupts must be disabled when changing prescaler setting to make sure the write procedure is
not interrupted.
The CKDIV8 Fuse determines the initial value of the CLKPS bits. If CKDIV8 is unprogrammed,
the CLKPS bits will be reset to “0000”. If CKDIV8 is programmed, CLKPS bits are reset to
“0011”, giving a division factor of eight at start up. This feature should be used if the selected
clock source has a higher frequency than the maximum frequency of the device at the present
operating conditions. Note that any value can be written to the CLKPS bits regardless of the
CKDIV8 Fuse setting. The Application software must ensure that a sufficient division factor is
chosen if the selcted clock source has a higher frequency than the maximum frequency of the
device at the present operating conditions. The device is shipped with the CKDIV8 Fuse
programmed.
Table 6-13.
Clock Prescaler Select
CLKPS3
CLKPS2
CLKPS1
CLKPS0
Clock Division Factor
0
000
1
0
001
2
0
010
4
0
011
8
0
100
16
0
101
32
0
110
64
0
111
128
1
000
256
1
001
Reserved
1
010
Reserved
1
011
Reserved
1
100
Reserved
相关PDF资料
PDF描述
R5F2L38CCNFA 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP80
R5F2L388CNFP 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP80
R5F2L3A8CNFA 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100
R5F2L36CCNFP 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP64
R5F2L367CDFA 8-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP64
相关代理商/技术参数
参数描述
R5F2L3ACCDFA#U0 功能描述:MCU 128KB ROM 10KB RAM 100LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:R8C/Lx/3AC 标准包装:250 系列:80C 核心处理器:8051 芯体尺寸:8-位 速度:16MHz 连通性:EBI/EMI,I²C,UART/USART 外围设备:POR,PWM,WDT 输入/输出数:40 程序存储器容量:- 程序存储器类型:ROMless EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4.5 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:68-LCC(J 形引线) 包装:带卷 (TR)
R5F2L3ACCDFP#V0 功能描述:MCU 128KB ROM 10KB RAM 100-LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:R8C/Lx/3AC 标准包装:250 系列:80C 核心处理器:8051 芯体尺寸:8-位 速度:16MHz 连通性:EBI/EMI,I²C,UART/USART 外围设备:POR,PWM,WDT 输入/输出数:40 程序存储器容量:- 程序存储器类型:ROMless EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4.5 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:68-LCC(J 形引线) 包装:带卷 (TR)
R5F2L3ACCNFA#U0 功能描述:MCU 128KB ROM 10KB RAM 100-LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:R8C/Lx/3AC 标准包装:250 系列:80C 核心处理器:8051 芯体尺寸:8-位 速度:16MHz 连通性:EBI/EMI,I²C,UART/USART 外围设备:POR,PWM,WDT 输入/输出数:40 程序存储器容量:- 程序存储器类型:ROMless EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4.5 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:68-LCC(J 形引线) 包装:带卷 (TR)
R5F2L3ACCNFP#30 制造商:Renesas Electronics Corporation 功能描述:IC MCU 16BIT 128KB FLASH 100LQFP
R5F2L3ACCNFP#U1 制造商:Renesas Electronics Corporation 功能描述: