收藏本站
参数资料
型号： R5F56218BDBG#U0
厂商： Renesas Electronics America
文件页数： 11/148页
文件大小： 0K
描述： MCU 32BIT FLASH 512KROM 176LFBGA
产品培训模块： RX Compare Match Timer
RX DMAC
标准包装： 1
系列： RX600
核心处理器： RX
芯体尺寸： 32-位
速度： 100MHz
连通性： CAN，EBI/EMI，I²C，SCI，SPI，USB
外围设备： DMA，LVD，POR，PWM，WDT
输入/输出数： 126
程序存储器容量： 512KB（512K x 8）
程序存储器类型： 闪存
RAM 容量： 96K x 8
电压 - 电源 (Vcc/Vdd)： 2.7 V ~ 3.6 V
数据转换器： A/D 8x10/12b，D/A 2x10b
振荡器型： 内部
工作温度： -40°C ~ 85°C
封装/外壳： 176-LFBGA
包装： 托盘
PIC18F6520/8520/6620/8620/6720/8720
DS39609B-page 106
2004 Microchip Technology Inc.
10.2
PORTB, TRISB and LATB
Registers
PORTB is an 8-bit wide, bidirectional port. The corre-
sponding data direction register is TRISB. Setting a
TRISB bit (= 1) will make the corresponding PORTB
pin an input (i.e., put the corresponding output driver in
a high-impedance mode). Clearing a TRISB bit (= 0)
will make the corresponding PORTB pin an output (i.e.,
put the contents of the output latch on the selected pin).
The Data Latch register (LATB) is also memory
mapped. Read-modify-write operations on the LATB
register, read and write the latched output value for
PORTB.
EXAMPLE 10-2:
INITIALIZING PORTB
Each of the PORTB pins has a weak internal pull-up. A
single control bit can turn on all the pull-ups. This is
performed by clearing bit RBPU (INTCON2<7>). The
weak pull-up is automatically turned off when the port
pin is configured as an output. The pull-ups are
disabled on a Power-on Reset.
Four of the PORTB pins (RB3:RB0) are the external
interrupt pins, INT3 through INT0. In order to use these
pins as external interrupts, the corresponding TRISB
bit must be set to ‘1’.
The other four PORTB pins (RB7:RB4) have an inter-
rupt-on-change feature. Only pins configured as inputs
can cause this interrupt to occur (i.e., any RB7:RB4 pin
configured as an output is excluded from the interrupt-
on-change comparison). The input pins (of RB7:RB4)
are compared with the old value latched on the last
read of PORTB. The “mismatch” outputs of RB7:RB4
are OR’ed together to generate the RB Port Change
Interrupt with Flag bit, RBIF (INTCON<0>).
This interrupt can wake the device from Sleep. The
user, in the Interrupt Service Routine, can clear the
interrupt in the following manner:
a)
Any read or write of PORTB (except with the
MOVFF
instruction). This will end the mismatch
condition.
b)
Clear flag bit RBIF.
A mismatch condition will continue to set flag bit, RBIF.
Reading PORTB will end the mismatch condition and
allow flag bit RBIF to be cleared.
The interrupt-on-change feature is recommended for
wake-up on key depression operation and operations
where PORTB is only used for the interrupt-on-change
feature. Polling of PORTB is not recommended while
using the interrupt-on-change feature.
RB3 can be configured by the configuration bit
CCP2MX, as the alternate peripheral pin for the CCP2
module. This is only available when the device is
configured in Microprocessor, Microprocessor with
Boot Block, or Extended Microcontroller operating
modes.
The RB5 pin is used as the LVP programming pin.
When the LVP configuration bit is programmed, this pin
loses the I/O function and become a programming test
function.
FIGURE 10-5:
BLOCK DIAGRAM OF
RB7:RB4 PINS
Note:
On a Power-on Reset, these pins are
configured as digital inputs.
CLRF
PORTB
; Initialize PORTB by
; clearing output
; data latches
CLRF
LATB
; Alternate method
; to clear output
; data latches
MOVLW
0xCF
; Value used to
; initialize data
; direction
MOVWF
TRISB
; Set RB<3:0> as inputs
; RB<5:4> as outputs
; RB<7:6> as inputs
Note:
When LVP is enabled, the weak pull-up on
RB5 is disabled.
Data Latch
From other
RBPU(2)
P
VDD
I/O pin(1)
Q
D
CK
Q
D
CK
QD
EN
QD
EN
Data Bus
WR LATB
WR TRISB
Set RBIF
TRIS Latch
RD TRISB
RD PORTB
RB7:RB4 pins
Weak
Pull-up
RD PORTB
Latch
TTL
Input
Buffer
ST
Buffer
RB7:RB5 in Serial Programming Mode
Q3
Q1
RD LATB
or PORTB
Note 1:
I/O pins have diode protection to VDD and VSS.
2:
To enable weak pull-ups, set the appropriate TRIS bit(s)
and clear the RBPU bit (INTCON2<7>).
相关PDF资料
PDF描述
MAX9205EAI/V+ IC SERIALIZER BUS/LVDS 28SSOP
VI-BVM-IX-F3 CONVERTER MOD DC/DC 10V 75W
CONN012 CONN N-MALE R/A END CRIMP RG-174
MS27497E18A66S CONN RCPT 66POS WALL MNT W/SCKT
CONN007 CONN N-MALE END CRIMP RG-174
相关代理商/技术参数
参数描述
R5F56218BDFB 制造商:Renesas Electronics Corporation 功能描述:MCU 32BIT RX621 144QFP
R5F56218BDFB#V0 功能描述:MCU 32BIT FLASH 512K ROM 144LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:RX600 标准包装:96 系列:PIC® 16F 核心处理器:PIC 芯体尺寸:8-位 速度:20MHz 连通性:I²C，SPI 外围设备:欠压检测/复位，POR，PWM，WDT 输入/输出数:11 程序存储器容量:3.5KB（2K x 14） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:128 x 8 电压 - 电源 (Vcc/Vdd):2.3 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 包装:管件
R5F56218BDFP 制造商:Renesas Electronics Corporation 功能描述:MCU 32BIT RX621 100QFP
R5F56218BDFP#V0 功能描述:MCU 32BIT FLASH 512KROM 100LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:RX600 标准包装:1 系列:87C 核心处理器:MCS 51 芯体尺寸:8-位 速度:16MHz 连通性:SIO 外围设备:- 输入/输出数:32 程序存储器容量:8KB（8K x 8） 程序存储器类型:OTP EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4 V ~ 6 V 数据转换器:- 振荡器型:外部 工作温度:0°C ~ 70°C 封装/外壳:44-DIP 包装:管件 其它名称:864285
R5F56218BDLD 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:100 MHz 32-bit RX MCU with FPU, 165 DMIPS, up to 512-Kbyte Flash, Ethernet, USB 2.0
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*