参数资料
型号: RDER72E683K3M1C11A
厂商: Murata Electronics North America
文件页数: 19/57页
文件大小: 0K
描述: CAP CER 0.068UF 250V 10% RADIAL
标准包装: 2,000
系列: RDE
电容: 0.068µF
电压 - 额定: 250V
容差: ±10%
温度系数: X7R
安装类型: 通孔
工作温度: -55°C ~ 125°C
应用: 通用
封装/外壳: 径向
尺寸/尺寸: 0.197" L x 0.124" W(5.00mm x 3.15mm)
高度 - 座高(最大): 0.248"(6.30mm)
引线间隔: 0.197"(5.00mm)
包装: 带盒(TB)
引线型: 纽结
! Note ? Please read rating and ! CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
? This catalog has only typical speci?cations. Therefore, please approve our product speci?cations or transact the approval sheet for product speci?cations before ordering.
C49E.pdf
Mar.12,2014
High Dielectric Constant Type Speci?cations and Test Methods
1
No. AEC-Q200 Test Item
Specifications
AEC-Q200 Test Method
1
Pre-and Post-Stress
Electrical Test
High Temperature
The measured and observed characteristics should satisfy the
Exposure (Storage) specifications in the following table.
Appearance No defects or abnormalities
2
Capacitance
Change
D.F.
I.R.
Temperature
Cycling
Within ±12.5%
0.04 max.
More than 1,000M Ω or 50M Ω · μF (Whichever is smaller)
The measured and observed characteristics should satisfy the
specifications in the following table.
Sit the capacitor for 1,000±12h at 150±3°C. Let sit for 24±2h at
room temperature, then measure.
Perform the 1,000 cycles according to the four heat treatments
listed in the following table. Let sit for 24±2h at *room condition,
Appearance No defects or abnormalities
then measure.
3
Capacitance
Change
D.F.
I.R.
Moisture
Resistance
Within ±12.5%
0.05 max.
1,000M Ω or 50M Ω · μF min. (Whichever is smaller)
The measured and observed characteristics should satisfy the
specifications in the following table.
Step 1 2 3 4
Temp. (°C) -55+0/-3 Room Temp. 125+3/-0 Room Temp.
Time (min.) 15±3 1 15±3 1
Perform the heat treatment at 150+0/-10°C for 60±5min and
then let sit for 24±2h at *room condition.
Apply the 24h heat (25 to 65°C) and humidity (80 to 98%)
treatment shown below, 10 consecutive times.
Appearance No defects or abnormalities
Let sit for 24±2h at *room condition, then measure.
Humidity
Humidity Humidity Humidity
Humidity
Capacitance
Change
Within ±12.5%
(°C)
70
65
90-98%
80-98% 90-98%
80-98%
90-98%
60
-2 °C
4
D.F.
I.R.
0.05 max.
500M Ω or 25M Ω · μF min. (Whichever is smaller)
55
50
45
40
35
30
25
20
15
10
5
0
+10
Initial measurement
-5
-10
One cycle = 24 hours
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Hours
Biased Humidity
The measured and observed characteristics should satisfy the
specifications in the following table.
Appearance No defects or abnormalities
Apply the rated voltage and DC1.3+0.2/-0V (add 6.8k Ω resistor)
5
Capacitance
Change
D.F.
I.R.
Operational Life
Within ±12.5%
0.05 max.
500M Ω or 25M Ω · μF min. (Whichever is smaller)
The measured and observed characteristics should satisfy the
specifications in the following table.
at 85±3°C and 80 to 85% humidity for 1,000±12h.
Remove and let sit for 24±2h at *room condition, then measure.
The charge/discharge current is less than 50mA.
Apply the voltage shown in the table for 1,000±12h at 125±3°C.
Let sit for 24±2h at *room condition, then measure.
Appearance No defects or abnormalities
The charge/discharge current is less than 50mA.
6
Capacitance
Change
Within ±12.5%
Apply test voltage for 60±5min at test temperature.
Remove and let sit for 24±2h at *room condition.
D.F.
I.R.
0.04 max.
1,000M Ω or 50M Ω · μF min. (Whichever is smaller)
Rated Voltage
DC25V, DC50V, DC100V
DC250V
DC630V
DC1kV
Test Voltage
200% of the rated voltage *1
150% of the rated voltage
120% of the rated voltage
110% of the rated voltage
7
External Visual
No defects or abnormalities
Visual inspection
8
Physical Dimension Within the specified dimensions
Using calipers and micrometers.
9
Marking
To be easily legible.
Visual inspection
* “room condition” Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmosphere pressure: 86 to 106kPa
*1: below parts are applicable in rated voltage×150%.
Char. Rated Voltage Capacitance
Dimensions
R7
R7
C7
C7
2A
2A
2A
2A
334
474-105
155-225
475
1
2
3
W
Continued on the following page.
17
相关PDF资料
PDF描述
DG333ADW-T1-E3 IC SWITCH QUAD SPDT 20SOIC
RDER72E104K3M1C11A CAP CER 0.1UF 250V 10% RADIAL
DEHR33D272KB3B CAP CER 2700PF 2KV 10% RADIAL
RPER71H154K2S1C03A CAP CER 0.15UF 50V 10% RADIAL
RPER71H154K2M1C03A CAP CER 0.15UF 50V 10% RADIAL
相关代理商/技术参数
参数描述
RDER72H102K1K1H03B 功能描述:CAP CER 1000PF 500V X7R RADIAL 制造商:murata electronics north america 系列:RDE 包装:剪切带(CT) 零件状态:在售 电容:1000pF 容差:±10% 电压 - 额定:500V 温度系数:X7R 工作温度:-55°C ~ 125°C 特性:- 等级:- 应用:通用 故障率:- 安装类型:通孔 封装/外壳:径向 大小/尺寸:0.177" 长 x 0.124" 宽(4.50mm x 3.15mm) 高度 - 安装(最大值):0.197"(5.00mm) 厚度(最大值):- 引线间距:0.197"(5.00mm) 引线形式:成型引线 标准包装:500
RDER72H102K2K1C11B 功能描述:多层陶瓷电容器MLCC - 含引线 1000pF 500volt X7R +/-10% RoHS:否 制造商:AVX 电容:470 pF 容差:10 % 电压额定值:3 kV 端接类型:Radial 工作温度范围: 温度系数/代码:X7R 引线间隔:5.08 mm 产品:Automotive MLCCs 引线类型:
RDER72H103K1K1H03B 功能描述:CAP CER 10000PF 50V X7R RADIAL 制造商:murata electronics north america 系列:RDE 包装:散装 零件状态:在售 电容:10000pF 容差:±10% 电压 - 额定:500V 温度系数:X7R 工作温度:-55°C ~ 125°C 特性:- 等级:- 应用:通用 故障率:- 安装类型:通孔 封装/外壳:径向 大小/尺寸:0.177" 长 x 0.124" 宽(4.50mm x 3.15mm) 高度 - 安装(最大值):0.197"(5.00mm) 厚度(最大值):- 引线间距:0.197"(5.00mm) 引线形式:成型引线 标准包装:500
RDER72H103K2K1C11B 功能描述:CAP CER 10000PF 500V 10% RADIAL RoHS:是 类别:电容器 >> 陶瓷 系列:RDE 标准包装:4,000 系列:- 电容:1000pF 电压 - 额定:50V 容差:±10% 温度系数:X7R 安装类型:表面贴装,MLCC 工作温度:-55°C ~ 125°C 应用:自动 额定值:AEC-Q200 封装/外壳:0805(2012 公制) 尺寸/尺寸:0.079" L x 0.047" W(2.00mm x 1.20mm) 高度 - 座高(最大):- 厚度(最大):- 引线间隔:- 特点:- 包装:带卷 (TR) 引线型:-
RDER72H104K8K1C11B 功能描述:CAP CER 0.1UF 500V 10% RADIAL RoHS:是 类别:电容器 >> 陶瓷 系列:RDE 标准包装:4,000 系列:- 电容:1000pF 电压 - 额定:50V 容差:±10% 温度系数:X7R 安装类型:表面贴装,MLCC 工作温度:-55°C ~ 125°C 应用:自动 额定值:AEC-Q200 封装/外壳:0805(2012 公制) 尺寸/尺寸:0.079" L x 0.047" W(2.00mm x 1.20mm) 高度 - 座高(最大):- 厚度(最大):- 引线间隔:- 特点:- 包装:带卷 (TR) 引线型:-