- 您现在的位置：买卖IC网 > PDF目录18781 > RXM-900-HP3-PPO_ (Linx Technologies Inc)RECEIVER RF 900MHZ 8-CHANNEL PDF资料下载
参数资料
| 型号： | RXM-900-HP3-PPO_ |
| 厂商： | Linx Technologies Inc |
| 文件页数： | 10/13页 |
| 文件大小： | 0K |
| 描述： | RECEIVER RF 900MHZ 8-CHANNEL |
| 产品变化通告： | Internal Component Change 25/Aug/2011 |
| 标准包装： | 10 |
| 系列： | HP3 |
| 频率： | 902MHz ~ 928MHz |
| 灵敏度： | -100dBm |
| 数据传输率 - 最大： | 56 kbps |
| 调制或协议： | FM，FSK |
| 应用： | 家庭/工业自动化，远程访问，安全警报 |
| 电流 - 接收： | 18mA |
| 数据接口： | PCB，通孔 |
| 天线连接器： | 通孔 |
| 特点： | 多通道，模拟和数字数据 |
| 电源电压： | 2.8 V ~ 13 V |
| 工作温度： | -30°C ~ 85°C |
| 封装/外壳： | 18-SIP |
| 供应商设备封装： | 18-SIP |
| 包装： | 管件 |
| 其它名称： | RXM-900-HP3-PPO_-ND |
task. A professionally designed
for practical or ergonomic reasons, thus,
an alternative antenna style such as a
helical, loop, or patch may be utilized
4. In many antenna designs, particularly 1/4-wave
whips, the ground plane acts as a counterpoise,
forming, in essence, a 1/2-wave dipole. For this
DIPOLE
reason, adequate ground plane area is essential.
surface area > the overall length of the 1/4-wave
radiating element. This is often not practical due to
instances, a designer must make the best use of the
0.1 μ F
it is often advantageous to share a single
antenna. To accomplish this, an antenna
switch must be used to provide isolation
between the modules so that the full
sensitive front end of the receiver. There
are a wide variety of antenna switches that
are cost-effective and easy to use. Among
ANTENNA CONSIDERATIONS
The choice of antennas is a critical
and often overlooked design
consideration. The range,
performance, and legality of an RF link
are critically dependent upon the
antenna. While adequate antenna
performance can often be obtained by
trial and error methods, antenna
design and matching is a complex
Figure 21: Linx Antennas
antenna, such as those from Linx, will
help ensure maximum performance and FCC compliance.
Linx transmitter modules typically have an output power that is slightly higher
than the legal limits. This allows the designer to use an inefficient antenna, such
as a loop trace or helical, to meet size, cost, or cosmetic requirements and still
achieve full legal output power for maximum range. If an efficient antenna is
used, then some attenuation of the output power will likely be needed. This can
easily be accomplished by using the LADJ line or a T-pad attenuator. For more
details on T-pad attenuator design, please see Application Note AN-00150.
A receiver antenna should be optimized for the frequency or band in which the
receiver operates and to minimize the reception of off-frequency signals. The
efficiency of the receiver’s antenna is critical to maximizing range performance.
Unlike the transmitter antenna, where legal operation may mandate attenuation
or a reduction in antenna efficiency, the receiver’s antenna should be optimized
as much as is practical.
It is usually best to utilize a basic quarter-wave whip until your prototype product
is operating satisfactorily. Other antennas can then be evaluated based on the
cost, size, and cosmetic requirements of the product. You may wish to review
Application Note AN-00500 “Antennas: Design, Application, Performance”
ANTENNA SHARING
In cases where a transmitter and receiver
module are combined to form a transceiver, VDD
Transmitter
Module 0.1 μ F
Antenna
0.1 μ F
GND
0.1 μ F
GND
Receiver
transmitter output power is not put on the Module
0.1 μ F
Select
Figure 22: Typical Antenna Switch
the most popular are switches from Macom and NEC. Look for an antenna
switch that has high isolation and low loss at the desired frequency of operation.
Generally, the Tx or Rx status of a switch will be controlled by a product’s
GENERAL ANTENNA RULES
The following general rules should help in maximizing antenna performance.
1. Proximity to objects such as a user’s hand, body, or metal objects will cause an
antenna to detune. For this reason, the antenna shaft and tip should be
positioned as far away from such objects as possible.
2. Optimum performance will be obtained
from a 1/4- or 1/2-wave straight whip
mounted at a right angle to the ground
plane. In many cases, this isn’t desirable
OPTIMUM
NOT RECOMMENDED
USEABLE
Figure 23: Ground Plane Orientation
and the corresponding sacrifice in performance accepted.
3. If an internal antenna is to be used, keep it away from other metal components,
particularly large items like transformers, batteries, PCB tracks, and ground
planes. In many cases, the space around the antenna is as important as the
antenna itself. Objects in close proximity to the antenna can cause direct
detuning, while those farther away will alter the antenna’s symmetry.
VERTICAL λ /4 GROUNDED
ANTENNA (MARCONI)
E
ELEMENT
λ /4
The ground plane can be a metal case or ground-fill I
areas on a circuit board. Ideally, it should have a
GROUND
PLANE
VIRTUAL λ /4 λ /4
DIPOLE
size and configuration constraints. In these
Figure 24: Dipole Antenna
area available to create as much ground plane as
possible in proximity to the base of the antenna. In cases where the antenna is
remotely located or the antenna is not in close proximity to a circuit board,
ground plane, or grounded metal case, a metal plate may be used to maximize
the antenna’s performance.
5. Remove the antenna as far as possible from potential interference sources. Any
frequency of sufficient amplitude to enter the receiver’s front end will reduce
system range and can even prevent reception entirely. Switching power
supplies, oscillators, or even relays can also be significant sources of potential
interference. The single best weapon against such problems is attention to
placement and layout. Filter the module’s power supply with a high-frequency
bypass capacitor. Place adequate ground plane under potential sources of noise
to shunt noise to ground and prevent it from coupling to the RF stage. Shield
noisy board areas whenever practical.
6. In some applications, it is advantageous to
place the module and antenna away from the
(MAY BE NEEDED)
microprocessor, but the user may also make the selection manually. In some
cases, where the characteristics of the Tx and Rx antennas need to be different
or antenna switch losses are unacceptable, it may be more appropriate to utilize
two discrete antennas.
Page 18
main equipment. This can avoid interference
problems and allows the antenna to be
oriented for optimum performance. Always use
50 Ω coax, like RG-174, for the remote feed.
CASE
GROUND PLANE
NUT
Figure 25: Remote Ground Plane
Page 19
相关PDF资料 |
PDF描述 |
|---|---|
| RXM-900-HP3-PPS_ | RECEIVER RF 900MHZ 8PAR/120SRLCH |
| RXM-900-HP3-SPO_ | RECEIVER RF 900MHZ 8-CH SMD |
| RXM-GPS-SG-B | GPS MODULE SMD SIRF |
| RXM-916-ES_ | RECEIVER RF 916MHZ 16PIN SMD |
| RXD-315-KH2 | RECEIVER RF 315MHZ SMT KH2 SER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| RXM-900-HP3-PPO_ | 功能描述:RECEIVER RF 900MHZ 8-CHANNEL RoHS:是 类别:RF/IF 和 RFID >> RF 接收器 系列:HP3 产品培训模块:Lead (SnPb) Finish for COTS 产品变化通告:Product Discontinuation 09/Jan/2012 标准包装:50 系列:* 频率:850MHz ~ 2.175GHz 灵敏度:- 数据传输率 - 最大:- 调制或协议:- 应用:* 电流 - 接收:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 特点:- 电源电压:4.75 V ~ 5.25 V 工作温度:0°C ~ 85°C 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| RXM-900-HP3-PPS | 功能描述:射频模块 RF Receiver 900MHz 8 & 100-CH SIP Pack RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| RXM-900-HP3-PPS_ | 功能描述:RECEIVER RF 900MHZ 8PAR/120SRLCH RoHS:是 类别:RF/IF 和 RFID >> RF 接收器 系列:HP3 产品培训模块:Lead (SnPb) Finish for COTS 产品变化通告:Product Discontinuation 09/Jan/2012 标准包装:50 系列:* 频率:850MHz ~ 2.175GHz 灵敏度:- 数据传输率 - 最大:- 调制或协议:- 应用:* 电流 - 接收:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 特点:- 电源电压:4.75 V ~ 5.25 V 工作温度:0°C ~ 85°C 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
| RXM-900-HP3-SPO | 功能描述:射频模块 RF Receiver 900MHz 8-CH SMD Pack RoHS:否 制造商:Linx Technologies 产品:Transceiver Modules 频带:902 MHz to 928 MHz 输出功率:- 15.5 dBm to + 12.5 dBm 接口类型:UART 工作电源电压:- 0.3 VDC to + 5.5 VDC 传输供电电流:38.1 mA 接收供电电流:22.7 mA 天线连接器类型:U.FL 最大工作温度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
| RXM-900-HP3-SPO_ | 功能描述:RECEIVER RF 900MHZ 8-CH SMD RoHS:是 类别:RF/IF 和 RFID >> RF 接收器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS 产品变化通告:Product Discontinuation 09/Jan/2012 标准包装:50 系列:* 频率:850MHz ~ 2.175GHz 灵敏度:- 数据传输率 - 最大:- 调制或协议:- 应用:* 电流 - 接收:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 特点:- 电源电压:4.75 V ~ 5.25 V 工作温度:0°C ~ 85°C 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。