- 您现在的位置：买卖IC网 > PDF目录25640 > S-7750C71XX-HCT1 SPECIALTY MICROPROCESSOR CIRCUIT, PBGA16 PDF资料下载
参数资料
| 型号： | S-7750C71XX-HCT1 |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | SPECIALTY MICROPROCESSOR CIRCUIT, PBGA16 |
| 封装： | 1.93 X 2.07 MM, 0.6 MM HEIGHT, LEAD FREE, WLP-16 |
| 文件页数： | 15/44页 |
| 文件大小： | 563K |
| 代理商： | S-7750C71XX-HCT1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
PROGRAMMABLE PORT CONTROLLER (PORT EXPANDER WITH BUILT-IN E2PROM CIRCUIT)
S-7750C
Rev.2.0_00
Seiko Instruments Inc.
22
6. 2 Write Protect
Write protect is available in the S-7750C. When the WP pin is connected to VCCH, the Write operation in all memory
area is inhibited. When the WP pin is connected to GND, Write protect becomes invalid so that the Write operation in
all memory area is accepted.
Fix the WP pin during the period; from rising of SCL at installing the last bit (B0) in Write data until the completion of
Write period (max. 5 ms). Written data in the address is not assured if the condition of the WP pin is changed during
this period. Be sure to connect the WP pin to GND when you don’t use Write Protect. Write Protect is valid in the
range of power supply voltage.
SDA
WP
SCL
Acknowledgment
signal
Period to fix WP pin
Stop
Condition
Start
Condition
Write Data
tWR
B0
Figure 27 Period to Fix WP Pin
6. 3 Acknowledgment polling
Acknowledge polling is used to find when the Write operation has completed. After receiving a stop condition the Write
operation has once started, all operations are inhibited to be performed so that the S-7750C cannot respond to the
signals transmitted from the master device. The master device sends a start condition, the device address and Read /
Write instruction code to the S-7750C (slave device), and detects the response from the slave device. It is possible to
find when the Write operation has completed. Thus if the slave device does not send an acknowledgment signal back,
the Write operation is in progress. If it sends an acknowledgment signal back, the Write operation has completed. Fix
the WP pin until an acknowledgment is confirmed. It is recommended to use the Read instruction “1” for the Read /
Write instruction code transmitted from the master device during acknowledgment polling.
6. 4 Irregular action
In the middle of inputting Write data, if inputting a stop condition in clock less than the specified data length (8-bit), the
S-7750C does not perform Write to the E
2PROM. And it either does not perform Write to the E2PROM if receiving a
stop condition after receiving data over 9-bit. However, data in the register has been rewritten at the point when the
S-7750C has received the specified length data. Be sure not to input clock which exceeds the specified value due to
noise or other causes.
相关PDF资料 |
PDF描述 |
|---|---|
| S-940-L55 | 3.18 mm SLOT WIDTH, 1 CHANNEL SLOTTED OPTICAL SWITCH LOGIC OUTPUT |
| S-940-W55 | 3.18 mm SLOT WIDTH, 1 CHANNEL SLOTTED OPTICAL SWITCH LOGIC OUTPUT |
| S153P | PIN PHOTO DIODE |
| S16MD01 | TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX |
| S16MD02 | TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S-7750C72XX-HCT1 | 制造商:SII 制造商全称:Seiko Instruments Inc 功能描述:PROGRAMMABLE PORT CONTROLLER (PORT EXPANDER WITH BUILT-IN E2PROM CIRCUIT) |
| S-7750C73XX-HCT1 | 制造商:SII 制造商全称:Seiko Instruments Inc 功能描述:PROGRAMMABLE PORT CONTROLLER (PORT EXPANDER WITH BUILT-IN E2PROM CIRCUIT) |
| S-7760A | 制造商:SII 制造商全称:Seiko Instruments Inc 功能描述:PROGRAMMABLE PORT CONTROLLER (PORT EXPANDER WITH BUILT-IN E2PROM CIRCUIT) |
| S-7760A00XX-HCT1 | 制造商:SII 制造商全称:Seiko Instruments Inc 功能描述:PROGRAMMABLE PORT CONTROLLER (PORT EXPANDER WITH BUILT-IN E2PROM CIRCUIT) |
| S-7760A00XX-TCT1G | 制造商:SII 制造商全称:Seiko Instruments Inc 功能描述:PROGRAMMABLE PORT CONTROLLER (PORT EXPANDER WITH BUILT-IN E2PROM CIRCUIT) |
发布紧急采购，3分钟左右您将得到回复。