- 您现在的位置：买卖IC网 > PDF目录299876 > S-8340A25AFT-T2 0.1 A SWITCHING CONTROLLER, 690 kHz SWITCHING FREQ-MAX, PDSO8 PDF资料下载
参数资料
| 型号： | S-8340A25AFT-T2 |
| 元件分类： | 稳压器 |
| 英文描述： | 0.1 A SWITCHING CONTROLLER, 690 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封装： | TSSOP-8 |
| 文件页数： | 10/53页 |
| 文件大小： | 855K |
| 代理商： | S-8340A25AFT-T2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页
STEP-UP, 600 kHz, PWM CONTROL OR PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER
S-8340/8341 Series
Rev.2.2_00
Seiko Instruments Inc.
18
4. Current Limit Circuit
The current limit circuit of the S-8340/8341 Series protects the external transistors from being damaged by heat due
to an overload or magnetic saturation of coils. Inserting a SENSE resistor (RSENSE) between the external FET
source or external NPN bipolar transistor emitter and Vss and entering a connection point with a sensor resistor into
the SENSE pin enables the current limit to function. Refer to “ Standard Circuit”.
A current limiting comparator in the IC monitors the SENSE pin for reaching the current limit detection voltage
(VSENSE
= 120 mV (typ.)). Upon detection of the voltage, the external transistor is held off for one clock of the
oscillator so that the current flowing in the external transistor is limited. At the ON signal of the next clock, the
external transistor is turned on and the current limit detection function is resumed.
However, this current limit circuit contains a CR filter with a time constant (
τ = 220 ns (typ.)) between the SENSE
pin and the current limiting comparator in the IC to prevent detection errors caused by the spike voltage generated
at the SENSE pin. If the time (pulse width tON : “H” level time at the EXT pin) after the external transistor turns on
until the current limit circuit operates is short, the current value that is actually limited becomes higher than the
current limit setting value determined by VSENSE/RSENSE as a side effect. The actual limit current value (ILIMIT) is
expressed by the following equation :
I
V
R
1e
LIMIT
SENSE
ton 0.5
CR
=÷
×
Remark CR in the equation is determined by the internal CR filter and varies in the range 116 to 470 ns (220 ns
(typ.).)
Caution Therefore, this current limit function does not guarantee full protection of external parts by ILIMIT
=
VSENSE/RSENSE under all operating conditions. Perform a thorough evaluation using the actual
devices.
For example, usage when the current value that the current limit circuit actually functions to raise the current limit
set value decided by VSENSE/RSENSE that includes usage under the conditions that the input voltage become close to
the output voltage or situations when the output voltage falls due to the activation of the current limit circuit and
become close to the input voltage.
Figure 12 shows an example of the actually measured increase of the peak current flowing through the coil when
the current limit circuit functions while the input voltage is nearing the output voltage.
Figure 13 shows an example of the actually measured increase of the peak current flowing through the coil when
the output voltage drops and approaches the input voltage by increasing the output current after the current limit
circuit functions.
Input Voltage (VIN) vs. Coil Peak Current (ILPEAK)
Output Current (IOUT) vs. Coil Peak Current (ILPEAK)
0
1
2
3
4
1
2
3
4
5
VIN (V)
IL
PEA
K(A
)
VSENSE / RSENSE
S-8340A50 (RSENSE
= 51 m)
0
1
2
3
4
1
2
3
IOUT (A)
IL
PEAK
(A
)
S-8340A50 (VIN
= 3V, RSENSE = 51 m)
Influence of CR filter
0
VSENSE / RSENSE
Current limit circuit
is activated
5
Figure 12 ILPEAK Measured at Activation of Current Limit
(VOUT Starts to Fall)
Figure 13 Measuring Coil Peak Current (ILPEAK)
If the current limit circuit is not used, remove RSENSE and connect the external transistor source or the emitter and
the SENSE pin to VSS.
相关PDF资料 |
PDF描述 |
|---|---|
| S-8351A28MC-J2NT2G | SWITCHING REGULATOR, 110 kHz SWITCHING FREQ-MAX, PDSO5 |
| S-93C56ADFJ | 128 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 |
| S-93C56BD0I-I8T1G | 128 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 |
| S-I6117#01 | 6A, 250VAC, FEMALE AND MALE, MAINS POWER CONNECTOR |
| S-T111B23MC-OGI-TF | 2.3 V FIXED POSITIVE LDO REGULATOR, PDSO5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S-8340A25AFT-T2-G | 功能描述:DC/DC 开关控制器 2.5V Step-Up 2.0% RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| S-8340A30AFT-T2 | 功能描述:DC/DC 开关控制器 3.0V Step-Up 2.0% RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| S-8340A30AFT-T2-G | 功能描述:DC/DC 开关控制器 3.0V Step-Up 2.0% RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| S-8340A33AFT-T2 | 功能描述:DC/DC 开关控制器 3.3V Step-Up 2.0% RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| S-8340A33AFT-T2-G | 功能描述:DC/DC 开关控制器 3.3V Step-Up 2.0% RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。