参数资料
型号: S116S02F
厂商: Sharp Microelectronics
文件页数: 8/13页
文件大小: 0K
描述: RELAY SSR 120VAC 16A ZC 4-SIP
产品目录绘图: S Series 4-SIP Circuit
标准包装: 200
系列: S116
电路: SPST-NO(1 Form A)
输出类型: AC,过零
负载电流: 16A
输入电压: 1.2VDC
电压 - 负载: 0 ~ 120 V
安装类型: 通孔
端接类型: PC 引脚
封装/外壳: 4-SIP
供应商设备封装: 4-SIP
包装: 管件
继电器类型: 继电器
其它名称: 425-2399-5
S116S02 Series
S216S02 Series
■ Design Considerations
● Recommended Operating Conditions
Parameter
Symbol
Conditions
MIN.
MAX.
Unit
Input
Input signal current at ON state
Input signal current at OFF state
I F (ON)
I F (OFF)
?
?
16
0
24
0.1
mA
mA
Load supply voltage
S116S02
S216S02
V OUT (rms)
?
80
80
120
240
V
Output
Load supply current
I OUT (rms)
Locate snubber circuit between output terminals
(Cs = 0.1 μ F, Rs = 47 ? )
0.1
I T (rms)
× 80%( ? )
mA
Frequency
Operating temperature
f
T opr
?
?
47
? 20
63
80
Hz
?C
( ? ) See Fig.2 about derating curve (I T (rms) vs. ambient temperature).
● Design guide
In order for the SSR to turn off, the triggering current (l F ) must be 0.1mA or less.
When the input current (I F ) is below 0.1mA, the output Triac will be in the open circuit mode. However, if the
voltage across the Triac, V D , increases faster than rated dV/dt, the Triac may turn on. To avoid this situation,
please incorporate a snubber circuit. Due to the many different types of load that can be driven, we can
merely recommend some circuit vales to start with : Cs=0.1 μ F and Rs=47 ? . The operation of the SSR and
snubber circuit should be tested and if unintentional switching occurs, please adjust the snubber circuit com-
ponent values accordingly.
When making the transition from On to Off state, a snubber circuit should be used ensure that sudden drops
in current are not accompanied by large instantaneous changes in voltage across the Triac.
This fast change in voltage is brought about by the phase difference between current and voltage.
Primarily, this is experienced in driving loads which are inductive such as motors and solenoids.
Following the procedure outlined above should provide sufficient results.
For over voltage protection, a Varistor may be used.
Any snubber or Varistor used for the above mentioned scenarios should be located as close to the main out-
put triac as possible.
Particular attention needs to be paid when utilizing SSRs that incorporate zero crossing circuitry.
If the phase difference between the voltage and the current at the output pins is large enough, zero crossing
type SSRs cannot be used. The result, if zero crossing SSRs are used under this condition, is that the SSR
may not turn on and off irregardless of the input current. In this case, only a non zero cross type SSR should
be used in combination with the above mentioned snubber circuit selection process.
The load current should be within the bounds of derating curve. (Refer to Fig.2)
Also, please use the optional heat sink when necessary.
In case the optional heat sink is used and the isolation voltage between the device and the optional heat sink
is needed, please locate the insulation sheet between the device and the heat sink.
When the optional heat sink is equipped, please set up the M3 screw-fastening torque at 0.3 to 0.5N?m.
In order to dissipate the heat generated from the inside of device effectively, please follow the below sugges-
tions.
Sheet No.: D4-A02701EN
8
相关PDF资料
PDF描述
PVU414SPBF IC RELAY PHOTOVO 400V 140MA 6SMD
0395337002 5.08MM EURO PLUG STR GRN 2POS
0395324003 5.08MM EURO HEADER RA BLK 3POS
S216S02F RELAY SSR 240VAC 16A ZC 4-SIP
0395314003 5.08MM EURO HEADER STR BLK 3POS
相关代理商/技术参数
参数描述
S116W 制造商:Pass & Seymour/Legrand 功能描述:1G 16 CU. IN. SWG BRKT OLD WORK
S117 制造商:DFX 功能描述:STRIPLIGHT LED 700MM COLD PEARL
S117/B/50 制造商:Aavid Thermalloy 功能描述:Heat sink,2.3deg C/W 97x50x25mm 33.5g
S117/B/75 制造商:Aavid Thermalloy 功能描述:Heat sink,1.8deg C/W 97x75x25mm 33.5g
S-1170 制造商:SII 制造商全称:Seiko Instruments Inc 功能描述:HIGH RIPPLE-REJECTION AND LOW DROPOUT HIGH OUTPUT CURRENT CMOS VOLTAGE REGULATOR