- 您现在的位置：买卖IC网 > PDF目录225140 > S29AL008D90MFI011 (SPANSION LLC) 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory PDF资料下载
参数资料
| 型号： | S29AL008D90MFI011 |
| 厂商： | SPANSION LLC |
| 元件分类： | PROM |
| 英文描述： | 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| 中文描述： | 512K X 16 FLASH 3V PROM, 90 ns, PDSO44 |
| 封装： | LEAD FREE, MO-180AAA, SOP-44 |
| 文件页数： | 16/52页 |
| 文件大小： | 2004K |
| 代理商： | S29AL008D90MFI011 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
February 27, 2009 S29AL008D_00_A11
S29AL008D
23
Data
She e t
8.5
Unlock Bypass Command Sequence
The unlock bypass feature allows the system to program bytes or words to the device faster than using the
standard program command sequence. The unlock bypass command sequence is initiated by first writing two
unlock cycles. This is followed by a third write cycle containing the unlock bypass command, 20h. The device
then enters the unlock bypass mode. A two-cycle unlock bypass program command sequence is all that is
required to program in this mode. The first cycle in this sequence contains the unlock bypass program
command, A0h; the second cycle contains the program address and data. Additional data is programmed in
the same manner. This mode dispenses with the initial two unlock cycles required in the standard program
command sequence, resulting in faster total programming time. Table 8.1 shows the requirements for the
command sequence.
During the unlock bypass mode, only the Unlock Bypass Program and Unlock Bypass Reset commands are
valid. To exit the unlock bypass mode, the system must issue the two-cycle unlock bypass reset command
sequence. The first cycle must contain the data 90h; the second cycle the data 00h. Addresses are don’t care
for both cycles. The device then returns to reading array data.
Table 8.1 illustrates the algorithm for the program operation. See Erase/Program Operations on page 39 for
parameters, and Figure 15.5 on page 39 for timing diagrams.
Figure 8.1 Program Operation
Note
See Table 8.1 on page 26 for program command sequence.
START
Write Program
Command Sequence
Data Poll
from System
Verify Data?
No
Yes
Last Address?
No
Yes
Programming
Completed
Increment Address
Embedded
Program
algorithm
in progress
相关PDF资料 |
PDF描述 |
|---|---|
| S29AL008D70MFI013 | 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| S29AL008D90MFI013 | 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| S29AL008D70MAI010 | 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| S29AL008D90MAI010 | 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| S29AL008D70MAI011 | 8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S29AL008D90MFI012 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| S29AL008D90MFI013 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| S29AL008D90MFI020 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| S29AL008D90MFI021 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
| S29AL008D90MFI022 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:8 Megabit (1 M x 8-Bit/512 K x 16-Bit) CMOS 3.0 Volt-only Boot Sector Flash Memory |
发布紧急采购，3分钟左右您将得到回复。