- 您现在的位置：买卖IC网 > PDF目录270895 > S29GL256N90FFI013 (Spansion Inc.) MirrorBit Flash Family PDF资料下载
参数资料
| 型号： | S29GL256N90FFI013 |
| 厂商： | Spansion Inc. |
| 英文描述： | MirrorBit Flash Family |
| 中文描述： | MirrorBit闪存系列 |
| 文件页数： | 79/110页 |
| 文件大小： | 2624K |
| 代理商： | S29GL256N90FFI013 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页当前第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页
70
S29GLxxxN MirrorBitTM Flash Family
27631A4 May 13, 2004
Adva nce
Inform at i o n
The Password Protection Command Set Exit command must be issued after
the execution of the commands listed previously to reset the device to read
mode. Otherwise the device will hang.
Note that issuing the Password Protection Command Set Exit command re-
enables reads and writes for the main memory.
Non-Volatile Sector Protection Command Set Definitions
The Non-Volatile Sector Protection Command Set permits the user to program the
Persistent Protection Bits (PPB bits), erase all of the Persistent Protection Bits
(PPB bits), and read the logic state of the Persistent Protection Bits (PPB bits).
The Non-Volatile Sector Protection Command Set Entry command se-
quence must be issued prior to any of the commands listed following to enable
proper command execution.
Note that issuing the Non-Volatile Sector Protection Command Set Entry
command disables reads and writes for the main memory.
PPB Program Command
The PPB Program command is used to program, or set, a given PPB bit. Each PPB
bit is individually programmed (but is bulk erased with the other PPB bits). The
specific sector address (A24-A16 for S29GL512N, A23-A16 for S29GL256N, A22-
A16 for S29GL128N) is written at the same time as the program command. If the
PPB Lock Bit is set to the “freeze state”, the PPB Program command will not exe-
cute and the command will time-out without programming the PPB bit.
All PPB Erase Command
The All PPB Erase command is used to erase all PPB bits in bulk. There is no
means for individually erasing a specific PPB bit. Unlike the PPB program, no spe-
cific sector address is required. However, when the All PPB Erase command is
issued, all Sector PPB bits are erased in parallel. If the PPB Lock Bit is set to
“freeze state”, the ALL PPB Erase command will not execute and the command
will time-out without erasing the PPB bits.
The device will preprogram all PPB bits prior to erasing when issuing the All PPB
Erase command. Also note that the total number of PPB program/erase cycles has
the same endurance as the flash memory array.
PPB Status Read Command
The programming state of the PPB for a given sector can be verified by writing a
PPB Status Read Command to the device. This requires an initial access time
latency.
The Non-Volatile Sector Protection Command Set Exit command must be
issued after the execution of the commands listed previously to reset the device
to read mode.
Note that issuing the Non-Volatile Sector Protection Command Set Exit
command re-enables reads and writes for the main memory.
Global Volatile Sector Protection Freeze Command Set
The Global Volatile Sector Protection Freeze Command Set permits the user to set
the PPB Lock Bit and reading the logic state of the PPB Lock Bit.
The Global Volatile Sector Protection Freeze Command Set Entry com-
mand sequence must be issued prior to any of the commands listed following to
enable proper command execution.
相关PDF资料 |
PDF描述 |
|---|---|
| S29GL256N10FFI013 | MirrorBit Flash Family |
| S29AL016M90FFI013 | 16 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY |
| S29AL016M10FFI013 | 16 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY |
| S29GL256N80FFI020 | MirrorBit Flash Family |
| S29GL256N90FFI020 | MirrorBit Flash Family |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S29GL256N90FFIR10 | 制造商:Spansion 功能描述:Flash Mem Parallel 3.3V 256M-Bit 32M x 8/16M x 16 90ns 64-Pin Fortified BGA Tray |
| S29GL256N90FFIR22 | 制造商:Spansion 功能描述: |
| S29GL256N90TFIR10 | 制造商:Spansion 功能描述:NOR Flash Parallel 3.3V 256Mbit 32M/16M x 8bit/16bit 90ns 56-Pin TSOP Tray 制造商:Spansion 功能描述:Flash - NOR IC |
| S29GL256N90TFIR2 | 制造商:Spansion 功能描述: |
| S29GL256N90TFIR20 | 制造商:Spansion 功能描述:Flash Mem Parallel 3.3V 256M-Bit 32M x 8/16M x 16 90ns 56-Pin TSOP Tray 制造商:Spansion 功能描述:Flash - NOR IC |
发布紧急采购，3分钟左右您将得到回复。