- 您现在的位置：买卖IC网 > PDF目录270895 > S29GL256N90FFI013 (Spansion Inc.) MirrorBit Flash Family PDF资料下载
参数资料
| 型号： | S29GL256N90FFI013 |
| 厂商： | Spansion Inc. |
| 英文描述： | MirrorBit Flash Family |
| 中文描述： | MirrorBit闪存系列 |
| 文件页数： | 93/110页 |
| 文件大小： | 2624K |
| 代理商： | S29GL256N90FFI013 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页当前第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页
May 13, 2004 27631A4
S29GLxxxN MirrorBitTM Flash Family
83
Ad va nc e
Inform ati o n
read cycles.) But DQ2 cannot distinguish whether the sector is actively erasing or
is erase-suspended. DQ6, by comparison, indicates whether the device is actively
erasing, or is in Erase Suspend, but cannot distinguish which sectors are selected
for erasure. Thus, both status bits are required for sector and mode information.
Refer to Table 14 to compare outputs for DQ2 and DQ6.
Figure 6 shows the toggle bit algorithm in flowchart form, and the section “DQ2:
Toggle Bit II” explains the algorithm. See also the RY/BY#: Ready/Busy# subsec-
differences between DQ2 and DQ6 in graphical form.
Reading Toggle Bits DQ6/DQ2
Refer to Figure 6 for the following discussion. Whenever the system initially be-
gins reading toggle bit status, it must read DQ7–DQ0 at least twice in a row to
determine whether a toggle bit is toggling. Typically, the system would note and
store the value of the toggle bit after the first read. After the second read, the
system would compare the new value of the toggle bit with the first. If the toggle
bit is not toggling, the device has completed the program or erase operation. The
system can read array data on DQ7–DQ0 on the following read cycle.
However, if after the initial two read cycles, the system determines that the toggle
bit is still toggling, the system also should note whether the value of DQ5 is high
(see the section on DQ5). If it is, the system should then determine again
whether the toggle bit is toggling, since the toggle bit may have stopped toggling
just as DQ5 went high. If the toggle bit is no longer toggling, the device has suc-
cessfully completed the program or erase operation. If it is still toggling, the
device did not completed the operation successfully, and the system must write
the reset command to return to reading array data.
The remaining scenario is that the system initially determines that the toggle bit
is toggling and DQ5 has not gone high. The system may continue to monitor the
toggle bit and DQ5 through successive read cycles, determining the status as de-
scribed in the previous paragraph. Alternatively, it may choose to perform other
system tasks. In this case, the system must start at the beginning of the algo-
rithm when it returns to determine the status of the operation (top of Figure 6).
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program, erase, or write-to-buffer time has ex-
ceeded a specified internal pulse count limit. Under these conditions DQ5
produces a “1,” indicating that the program or erase cycle was not successfully
completed.
The device may output a “1” on DQ5 if the system tries to program a “1” to a
location that was previously programmed to “0.” Only an erase operation can
change a “0” back to a “1.” Under this condition, the device halts the opera-
tion, and when the timing limit has been exceeded, DQ5 produces a “1.”
In all these cases, the system must write the reset command to return the device
to the reading the array (or to erase-suspend-read if the device was previously
in the erase-suspend-program mode).
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the system may read DQ3 to de-
termine whether or not erasure has begun. (The sector erase timer does not
apply to the chip erase command.) If additional sectors are selected for erasure,
the entire time-out also applies after each additional sector erase command.
相关PDF资料 |
PDF描述 |
|---|---|
| S29GL256N10FFI013 | MirrorBit Flash Family |
| S29AL016M90FFI013 | 16 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY |
| S29AL016M10FFI013 | 16 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY |
| S29GL256N80FFI020 | MirrorBit Flash Family |
| S29GL256N90FFI020 | MirrorBit Flash Family |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S29GL256N90FFIR10 | 制造商:Spansion 功能描述:Flash Mem Parallel 3.3V 256M-Bit 32M x 8/16M x 16 90ns 64-Pin Fortified BGA Tray |
| S29GL256N90FFIR22 | 制造商:Spansion 功能描述: |
| S29GL256N90TFIR10 | 制造商:Spansion 功能描述:NOR Flash Parallel 3.3V 256Mbit 32M/16M x 8bit/16bit 90ns 56-Pin TSOP Tray 制造商:Spansion 功能描述:Flash - NOR IC |
| S29GL256N90TFIR2 | 制造商:Spansion 功能描述: |
| S29GL256N90TFIR20 | 制造商:Spansion 功能描述:Flash Mem Parallel 3.3V 256M-Bit 32M x 8/16M x 16 90ns 56-Pin TSOP Tray 制造商:Spansion 功能描述:Flash - NOR IC |
发布紧急采购，3分钟左右您将得到回复。