参数资料
| 型号： | SA5230NG |
| 厂商： | ON Semiconductor |
| 文件页数： | 3/18页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP LOW VOLTAGE 8-DIP |
| 标准包装： | 50 |
| 放大器类型： | 通用 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 0.25 V/µs |
| 增益带宽积： | 600kHz |
| 电流 - 输入偏压： | 40nA |
| 电压 - 输入偏移： | 400µV |
| 电流 - 电源： | 1.1mA |
| 电流 - 输出 / 通道： | 32mA |
| 电压 - 电源，单路/双路(±)： | 1.8 V ~ 15 V，±0.9 V ~ 7.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
NE5230, SA5230, SE5230
http://onsemi.com
11
What this means is that several instruments, such as a chart
recorder, a meter, or a controller, as well as a long cable, can
be connected in series on the loop and still obtain accurate
readings if the total resistance does not exceed 650
W.
Furthermore, any variation of resistance in this range will
not change the output current.
Any voltage output type transducer can be used, but one
that does not need external DC voltage or current excitation
to limit the maximum possible load resistance is preferable.
Even this problem can be surmounted if the supply power
needed by the transducer is compatible with the NE5230.
The power goes up the line to the transducer and amplifier
while the transducer signal is sent back via the current output
of the NE5230 transconductance configuration.
The voltage range on the input can be changed for
transducers that produce a large output by simply increasing
the current sense resistor to get the corresponding 4.0 to
20 mA output current. If a very long line is used which
causes high line resistance, a current repeater could be
inserted into the line. The same configuration of Figure 7 can
be used with exception of a resistor across the input and line
ground to convert the current back to voltage. Again, the
current sensing resistor will set up the transconductance and
the part will receive power from the line.
TEMPERATURE TRANSDUCER
A variation on the previous circuit makes use of the supply
current control pin. The voltage present at this pin is
proportional to absolute temperature (PTAT) because it is
produced by the amplifier bias current through an internal
resistor divider in a PTAT cell. If the control pin is connected
to the input pin, the NE5230 itself can be used as a
temperature transducer. If the center tap of a resistive pot is
connected to the control pin with one side to ground and the
other to the inverting input, the voltage can be changed to
give different temperature versus output current conditions
(Figure 8). For additional control, the output current is still
proportional to the input voltage differential divided by the
current sense resistor.
When using the NE5230 as a temperature transducer, the
thermal considerations in the previous section must be kept
in mind.
V
REMOTE
POWER
SUPPLY
NE5230
VCC
VEE
IOUT
3
2
4
5
6
7
+
RC
RL
+
NOTES:
1. IOUT = VIN/RC
2. RL MAX ≈
VREMOTE * 1.8V * VINMAX
IOUT
For RC = 1W
IOUT
4mA
20mA
VIN
4mV
20mV
200
Figure 8. NE5230 remote temperature transducer utilizing 4.0 20 mA current transmission. This application
shows the use of the accessibility of the PTAT cell in the device to make the part, itself, a transducer.
10W
相关PDF资料 |
PDF描述 |
|---|---|
| M80-8280822 | CONN HDR 2MM W/LATCH 8POS SMD |
| M80-8261422 | CONN HDR 2MM VERT 14POS SMD |
| SA18CA | TVS BIDIRECT 500W 18V DO-15 |
| SZP6SMB62CAT3G | TVS ZENER 600W 62V BIDIR SMB |
| 961238-6300-AR-PR | CONN HEADER STR DL 38PS GOLD SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SA5232 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Matched dual high-performance low-voltage operational amplifier |
| SA5232D | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Matched dual high-performance low-voltage operational amplifier |
| SA5232D,112 | 功能描述:运算放大器 - 运放 MATCHED DUAL LOW-VOLT OP AMP RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| SA5232D,118 | 功能描述:运算放大器 - 运放 MATCHED DUAL LOW-VOLT OP AMP RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| SA5232D/01 | 功能描述:运算放大器 - 运放 DUAL LVOP AMP -40-85 RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。