参数资料
型号: SAA7706H/N107,557
厂商: NXP Semiconductors
文件页数: 18/52页
文件大小: 0K
描述: IC CAR RADIO DSP 80-QFP
标准包装: 330
类型: 汽车信号处理器
接口: I²C,I²:S,LSB,SPDIF
电压 - 输入/输出: 3.30V
电压 - 核心: 3.30V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 80-BQFP
供应商设备封装: 80-QFP(14x20)
包装: 托盘
其它名称: 935267098557
SAA7706H/N107
SAA7706H/N107-ND
2001 Mar 05
25
Philips Semiconductors
Product specication
Car radio Digital Signal Processor (DSP)
SAA7706H
8.14
Digital serial inputs/outputs and SPDIF inputs
8.14.1
GENERAL DESCRIPTION DIGITAL SERIAL AUDIO
INPUTS
/OUTPUTS
For communication with external digital sources a digital
serial bus is implemented. It is a serial 3-line bus, having
one line for data, one line for clock and one line for the
word select. For external digital sources the SAA7706H
acts as a slave, so the external source is master and
supplies the clock.
The digital serial input is capable of handling multiple input
formats. The input is capable of handling Philips I2S-bus
and LSB-justified formats of 16, 18, 20 and 24 bits word
sizes. The sampling frequency can be either
44.1 or 48 kHz. See Fig.15 for the general waveform
formats of all possible formats.
The number of bit clock (BCK) pulses may vary in the
application. When the applied word length is smaller than
24 bits (internal resolution of DSP2), the LSB bits will get
internally a zero value; when the applied word length
exceeds 24 bits then the LSBs are skipped.
It should be noted that:
Two digital sources can not be used at the same time
Maximum number of bit clocks per word select (WS) is
limited to 64
The word select (WS) must have a duty cycle of 50%.
8.14.2
GENERAL DESCRIPTION SPDIF INPUTS (SPDIF1
AND
SPDIF2)
For communication with external digital sources also an
SPDIF input can be used. The two SPDIF input pins can
be connected via an analog multiplexer to the SPDIF
receiver. It is a receiver without an analog PLL that
samples the incoming SPDIF with a high frequency. In this
way the data is recovered synchronously on the applied
system clock.
From the SPDIF signal a three wire serial bus
(e.g. I2S-bus) is made, consisting of a word select, data
and bit clock line. The sample frequency fs depends solely
on the SPDIF signal input accuracy and both 44.1 and
48 kHz are supported.
This chip does not handle the user data bits, channel
status bits and validity bits of the SPDIF stream, but only
the audio is given at its outputs. Some rom_codes do take
care of the pre-emphasis bit of the SPDIF stream.
The bits in the audio space are always decoded regardless
of any status bits e.g. ‘copy protected’, ‘professional mode’
or ‘data mode’. The DAC is not muted in the event of a
non-linear PCM audio, however the bit is observable via
the I2C-bus. A few other channel status bits are available.
There are 5 control signals available from the SPDIF input
stage. These are connected to flags of DSP2. For more
details see separate manual.
These 5 control signals are:
Signals to indicate the sample frequency of the SPDIF
signal: 44.1 and 48 kHz (32 kHz is not supported)
A lock signal indicating if the SPDIF input is in lock
The pre-emphasis bit of the SPDIF audio stream
The pcm_audio/non-pcm_audio bit indicating if an audio
or data stream is detected. The FSDAC output will not
be muted in the event of a non-audio PCM stream. This
status bit can be read via the I2C-bus, the
microcontroller can decide to mute the DAC (via
pin POM).
The design fulfils the digital audio interface specification
“IEC 60958-1 Ed2, part 1, general part IEC 60958-3 Ed2,
part 3, consumer applications”.
It should be noted that:
The SPDIF input may only be used in the ‘consumer
mode’ specified in the digital audio interface
specification
Only one of the two SPDIF sources can be used
(selected) at the same time
The FSDAC will not (automatically) be muted in the
event of a non-audio stream
Two digital sources can not be used at the same time
Supported sample frequencies are 44.1 and 48 kHz.
相关PDF资料
PDF描述
VY2392M43Y5US6TV5 CAP CER 3900PF 300V 20% RADIAL
HMC25DRAH-S734 CONN EDGECARD 50POS .100 R/A PCB
TAP226M035HSB CAP TANT 22UF 35V 20% RADIAL
VE-25P-EU CONVERTER MOD DC/DC 13.8V 200W
RCB60DHBN CONN EDGECARD 120PS R/A .050 DIP
相关代理商/技术参数
参数描述
SAA7707H 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Car radio Digital Signal Processor CDSP
SAA7708H 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Car Radio Digital Signal Processor
SAA7709/N107 制造商:PHILIPS-SEMI 功能描述:
SAA7709H/N103 功能描述:音频 DSP DIGITAL SIGNAL PROCESSOR RoHS:否 制造商:Texas Instruments 工作电源电压: 电源电流: 工作温度范围: 安装风格: 封装 / 箱体: 封装:Tube
SAA7709H/N103,518 功能描述:音频 DSP DIRAC-2 RoHS:否 制造商:Texas Instruments 工作电源电压: 电源电流: 工作温度范围: 安装风格: 封装 / 箱体: 封装:Tube