参数资料
型号: SAB-C505-2R16M
厂商: INFINEON TECHNOLOGIES AG
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP44
封装: PLASTIC, MQFP-44
文件页数: 61/88页
文件大小: 1013K
代理商: SAB-C505-2R16M
C505/C505C/C505A/C505CA
Data Sheet
60
12.00
Note:
1) Capacitive loading on ports 0 and 2 may cause spurious noise pulses to be superimposed on the
VOL of ALE
and port 3. The noise is due to external bus capacitance discharging into the port 0 and port 2 pins when these
pins make 1-to-0 transitions during bus operation. In the worst case (capacitive loading > 100 pF), the noise
pulse on ALE line may exceed 0.8 V. In such cases it may be desirable to qualify ALE with a schmitt-trigger,
or use an address latch with a schmitt-trigger strobe input.
2) Capacitive loading on ports 0 and 2 may cause the
VOH on ALE and PSEN to momentarily fall below the
0.9
V
DD specification when the address lines are stabilizing.
3) Overload conditions under operating conditions occur if the voltage on the respective pin exceeds the specified
operating range (i.e.
VOV > VDD +0.5 V or VOV < VSS - 0.5 V). The absolute sum of input currents on all port
pins may not exceed 50 mA. The supply voltage
V
DD and VSS must remain within the specified limits.
4) Not 100% tested, guaranteed by design characterization.
5) Only valid for C505A-4E and C505CA-4E.
6) Only valid for C505A-4E and C505CA-4E in programming mode.
7)
I
DD (active mode) is measured with:
XTAL1 driven with
tR , tF = 5 ns, 50% duty cycle , VIL = VSS +0.5 V, VIH = VDD – 0.5 V; XTAL2 = N.C.;
EA =Port 0=RESET=
V
DD ; all other pins are disconnected.
8)
I
DD (idle mode) is measured with all output pins disconnected and with all peripherals disabled;
XTAL1 driven with
tR , tF = 5 ns, 50% duty cycle, VIL = VSS +0.5 V, VIH = VDD – 0.5 V; XTAL2 = N.C.;
RESET = EA =
VSS ; Port0 = VDD ; all other pins are disconnected; the microcontroller is put into idle mode by
software;
9)
I
DD (active mode with slow-down mode) is measured with all output pins disconnected and with all peripherals
disabled;
XTAL1 driven with
tR , tF = 5 ns, 50% duty cycle, VIL = VSS +0.5 V, VIH = VDD – 0.5 V; XTAL2 = N.C.;
RESET = EA =
VSS ; all other pins are disconnected; the microcontroller is put into slow-down mode by
software;
10)
I
DD (idle mode with slow-down mode) is measured with all output pins disconnected and with all peripherals
disabled;
XTAL1 driven with
tR , tF = 5 ns, 50% duty cycle, VIL = VSS +0.5 V, VIH = VDD – 0.5 V; XTAL2 = N.C.;
RESET = EA =
VSS ; Port0 = VDD ; all other pins are disconnected; the microcontroller is put into idle mode
with slow-down enabled by software;
11)
IPD (power-down mode) is measured under following conditions:
Port 0 = EA =
V
DD ; RESET =VSS ; XTAL2 = N.C.; XTAL1 = VSS ; VAGND = VSS ; VAREF = VDD ;
all other pins are disconnected.
12) The typical
I
DD values are periodically measured at TA = +25 °C but not 100% tested.
13) The maximum
I
DD values are measured under worst case conditions (TA = 0 °C or -40 °C and VDD =5.5 V)
14) The values are valid for C505CA-4R, C505CA-2R, C505CA-L, C505A-4R, C505A-2R and C505A-L only.
相关PDF资料
PDF描述
SAB-C505-2R20M 8-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP44
SAB-C515-RN 8-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQCC68
S1C88862F0A0100 MICROCONTROLLER, PQFP128
STM8AF6146TDXXXX MICROCONTROLLER, PQFP32
STM32F105RBT7XXX 32-BIT, FLASH, 72 MHz, RISC MICROCONTROLLER, PQFP64
相关代理商/技术参数
参数描述
SAB-C505-2RM 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:8-Bit CMOS Microcontroller
SAB-C505A-4EM 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:8-Bit CMOS Microcontroller
SAB-C505A-4EM-BA 制造商:Rochester Electronics LLC 功能描述:- Bulk
SAB-C505C-2RM 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:8-Bit CMOS Microcontroller
SAB-C505CA-4EM 制造商:Infineon Technologies 功能描述:Bulk