参数资料
型号: SAF-XE167HM-48FXXL
厂商: INFINEON TECHNOLOGIES AG
元件分类: 微控制器/微处理器
英文描述: RISC MICROCONTROLLER, PQFP144
封装: 0.50 MM PITCH, GREEN, PLASTIC, LQFP-144
文件页数: 94/140页
文件大小: 1096K
代理商: SAF-XE167HM-48FXXL
XE167FM, XE167GM, XE167HM, XE167KM
XE166 Family Derivatives / Base Line
Functional Description
Data Sheet
57
V2.0, 2009-03
3.6
Interrupt System
With a minimum interrupt response time of 7/111) CPU clocks (in the case of internal
program execution), the XE167xM can react quickly to the occurrence of non-
deterministic events.
The architecture of the XE167xM supports several mechanisms for fast and flexible
response to service requests; these can be generated from various sources internal or
external to the microcontroller. Any of these interrupt requests can be programmed to be
serviced by the Interrupt Controller or by the Peripheral Event Controller (PEC).
Where in a standard interrupt service the current program execution is suspended and
a branch to the interrupt vector table is performed, just one cycle is ‘stolen’ from the
current CPU activity to perform a PEC service. A PEC service implies a single byte or
word data transfer between any two memory locations with an additional increment of
either the PEC source pointer, the destination pointer, or both. An individual PEC
transfer counter is implicitly decremented for each PEC service except when performing
in the continuous transfer mode. When this counter reaches zero, a standard interrupt is
performed to the corresponding source-related vector location. PEC services are
particularly well suited to supporting the transmission or reception of blocks of data. The
XE167xM has eight PEC channels, each whith fast interrupt-driven data transfer
capabilities.
Each of the possible interrupt nodes has a separate control register containing an
interrupt request flag, an interrupt enable flag and an interrupt priority bitfield. Each node
can be programmed by its related register to one of sixteen interrupt priority levels. Once
accepted by the CPU, an interrupt service can only be interrupted by a higher-priority
service request. For standard interrupt processing, each possible interrupt node has a
dedicated vector location.
Fast external interrupt inputs can service external interrupts with high-precision
requirements. These fast interrupt inputs feature programmable edge detection (rising
edge, falling edge, or both edges).
Software interrupts are supported by the ‘TRAP’ instruction in combination with an
individual trap (interrupt) number.
Table 6 shows all of the possible XE167xM interrupt sources and the corresponding
hardware-related interrupt flags, vectors, vector locations and trap (interrupt) numbers.
Note: Interrupt nodes which are not assigned to peripherals (unassigned nodes) may be
used to generate software-controlled interrupt requests by setting the respective
interrupt request bit (xIR).
1) Depending if the jump cache is used or not.
相关PDF资料
PDF描述
SAF-XE167HM-72FXXL RISC MICROCONTROLLER, PQFP144
SAF-XE167KM-48FXXL RISC MICROCONTROLLER, PQFP144
SAF-XE167KM-72FXXL RISC MICROCONTROLLER, PQFP144
SAK-XE167FM-48FXXL RISC MICROCONTROLLER, PQFP144
SAK-XE167FM-72FXXL 32-BIT, FLASH, RISC MICROCONTROLLER, PQFP144
相关代理商/技术参数
参数描述
SAF-XE167HM-72F80L AA 功能描述:16位微控制器 - MCU 16 BIT FLASH C11 IMM RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
SAF-XE167K-48F66L 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:16-Bit Single-Chip Real Time Signal Controller
SAF-XE167K-48F66L AC 功能描述:16位微控制器 - MCU Integrated Circuits (ICs) Microcontrollers RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT
SAF-XE167K-48F66LAC 制造商:Rochester Electronics LLC 功能描述: 制造商:Infineon Technologies AG 功能描述:
SAF-XE167K-72F66L 制造商:INFINEON 制造商全称:Infineon Technologies AG 功能描述:16-Bit Single-Chip Real Time Signal Controller