- 您现在的位置：买卖IC网 > PDF目录11814 > SC16C2550IN40,112 (NXP Semiconductors)IC UART DUAL W/FIFO 40-DIP PDF资料下载
参数资料
| 型号： | SC16C2550IN40,112 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 45/46页 |
| 文件大小： | 0K |
| 描述： | IC UART DUAL W/FIFO 40-DIP |
| 标准包装： | 9 |
| 特点： | 2 通道 |
| 通道数： | 2，DUART |
| FIFO's： | 16 字节 |
| 电源电压： | 2.5V，3.3V，5V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 通孔 |
| 封装/外壳： | 40-DIP（0.600"，15.24mm） |
| 供应商设备封装： | 40-DIP |
| 包装： | 管件 |
| 其它名称： | 568-3262-5 935270024112 SC16C2550IN40 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页当前第45页第46页
Philips Semiconductors
SC16C2550
Dual UART with 16 bytes of transmit and receive FIFOs and IrDA
encoder/decoder
Product data
Rev. 03 — 19 June 2003
8 of 46
9397 750 11621
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
XTAL2
17
19
14
O
Output of the crystal oscillator or buffered clock. (See also XTAL1.)
Crystal oscillator output or buffered clock output. Should be left open if an
external clock is connected to XTAL1. For extended frequency operation,
this pin should be tied to VCC via a 2 k resistor.
CDA,
CDB
38, 19 42, 21
40, 16
I
Carrier Detect (Active-LOW). These inputs are associated with individual
UART channels A through B. A logic 0 on this pin indicates that a carrier
has been detected by the modem for that channel.
CTSA,
CTSB
36, 25 40, 28
38, 23
I
Clear to Send (Active-LOW). These inputs are associated with individual
UART channels, A through B. A logic 0 on the CTS pin indicates the
modem or data set is ready to accept transmit data from the SC16C2550.
Status can be tested by reading MSR[4]. This pin has no effect on the
UART’s transmit or receive operation.
DSRA,
DSRB
37, 22 41, 25
39, 20
I
Data Set Ready (Active-LOW). These inputs are associated with
individual UART channels, A through B. A logic 0 on this pin indicates the
modem or data set is powered-on and is ready for data exchange with the
UART. This pin has no effect on the UART’s transmit or receive operation.
DTRA,
DTRB
33, 34 37, 38
34, 35
O
Data Terminal REady (Active-LOW). These outputs are associated with
individual UART channels, A through B. A logic 0 on this pin indicates that
the SC16C2550 is powered-on and ready. This pin can be controlled via
the modem control register. Writing a logic 1 to MCR[0] will set the DTR
output to logic 0, enabling the modem. This pin will be a logic 1 after writing
a logic 0 to MCR[0], or after a reset. This pin has no effect on the UART’s
transmit or receive operation.
RIA, RIB
39, 23 43, 26
41, 21
I
Ring Indicator (Active-LOW). These inputs are associated with individual
UART channels, A through B. A logic 0 on this pin indicates the modem has
received a ringing signal from the telephone line. A logic 1 transition on this
input pin will generate an interrupt.
RTSA,
RTSB
32, 24 36, 27
33, 22
O
Request to Send (Active-LOW). These outputs are associated with
individual UART channels, A through B. A logic 0 on the RTS pin indicates
the transmitter has data ready and waiting to send. Writing a logic 1 in the
modem control register MCR[1] will set this pin to a logic 0, indicating data
is available. After a reset this pin will be set to a logic 1. This pin has no
effect on the UART’s transmit or receive operation.
RXA, RXB 10, 9
11, 10
5, 4
I
Receive data A, B. These inputs are associated with individual serial
channel data to the SC16C2550 receive input circuits, A-B. The RX signal
will be a logic 1 during reset, idle (no data), or when the transmitter is
disabled. During the local loop-back mode, the RX input pin is disabled and
TX data is connected to the UART RX input, internally.
TXA, TXB 11, 12 13, 14
7, 8
O
Transmit data A, B. These outputs are associated with individual serial
transmit channel data from the SC16C2550. The TX signal will be a logic 1
during reset, idle (no data), or when the transmitter is disabled. During the
local loop-back mode, the TX output pin is disabled and TX data is
internally connected to the UART RX input.
Table 2:
Pin description…continued
Symbol
Pin
Type Description
DIP40 PLCC44 LQFP48
相关PDF资料 |
PDF描述 |
|---|---|
| SC16C2550IA44,529 | IC UART DUAL W/FIFO 44-PLCC |
| SC16IS760IPW-S | IC UART I2C/SPI 24-TSSOP |
| V24C28H150BF3 | CONVERTER MOD DC/DC 28V 150W |
| MS27473E16B55P | CONN PLUG 55POS STRAIGHT W/PINS |
| MS3110F14-18S | CONN RCPT 18POS WALL MNT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC16C2552 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Dual UART with 16-byte transmit and receive FIFOs |
| SC16C2552B | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs |
| SC16C2552BIA44 | 功能描述:UART 接口集成电路 16CB 2.5V-5V 2CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16C2552BIA44,512 | 功能描述:UART 接口集成电路 16CB 2.5V-5V 2CH RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16C2552BIA44,518 | 功能描述:UART 接口集成电路 16CB 2.5V-5V 2CH RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。