- 您现在的位置：买卖IC网 > PDF目录1967 > SC16C650BIB48,151 (NXP Semiconductors)IC UART SINGLE W/FIFO 48-LQFP PDF资料下载
参数资料
| 型号： | SC16C650BIB48,151 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 6/48页 |
| 文件大小： | 0K |
| 描述： | IC UART SINGLE W/FIFO 48-LQFP |
| 产品培训模块： | Stand-Alone UARTs |
| 标准包装： | 250 |
| 通道数： | 1，UART |
| FIFO's： | 32 字节 |
| 电源电压： | 2.5V，3.3V，5V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
SC16C650B_4
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 14 September 2009
14 of 48
NXP Semiconductors
SC16C650B
UART with 32-byte FIFOs and IrDA encoder/decoder
6.8 DMA operation
The SC16C650B FIFO trigger level provides additional exibility to the user for block
mode operation. The user can optionally operate the transmit and receive FIFOs in the
DMA mode (FCR[3]). The DMA mode affects the state of the RXRDY and TXRDY output
Remark: DMA operation is not supported in the HVQFN32 package.
6.9 Sleep mode
The SC16C650B is designed to operate with low power consumption. A special Sleep
mode is included to further reduce power consumption when the chip is not being used.
With EFR[4] and IER[4] enabled (set to a logic 1), the SC16C650B enters the Sleep
mode, but resumes normal operation when a start bit is detected, a change of state on
any of the modem input pins RI, CTS, DSR, DCD, RX pin, or a transmit data is provided
by the user. If the Sleep mode is enabled and the SC16C650B is awakened by one of the
conditions described above, it will return to the Sleep mode automatically after the last
character is transmitted or read by the user. In any case, the Sleep mode will not be
entered while an interrupt(s) is pending. The SC16C650B will stay in the Sleep mode of
operation until it is disabled by setting IER[4] to a logic 0.
6.10 Loopback mode
The internal loopback capability allows on-board diagnostics. In the loopback mode, the
normal modem interface pins are disconnected and recongured for loopback internally.
MCR[3:0] register bits are used for controlling loopback diagnostic testing. In the loopback
mode, OUT1 (bit 2) and OUT2 (bit 3) in the MCR register control the modem RI and DCD
inputs, respectively. MCR signals DTR (bit 0) and RTS (bit 1) are used to control the
modem DSR and CTS inputs, respectively. The transmitter output (TX) and the receiver
input (RX) are disconnected from their associated interface pins, and instead are
connected together internally (see Figure 7). The CTS, DSR, DCD, and RI are
disconnected from their normal modem control input pins, and instead are connected
internally to DTR, RTS, OUT1 and OUT2. Loopback test data is entered into the Transmit
Holding Register via the user data bus interface, D0 to D7. The transmit UART serializes
the data and passes the serial data to the receive UART via the internal loopback
connection. The receive UART converts the serial data back into parallel data that is then
made available at the user data interface D0 to D7. The user optionally compares the
received data to the initial transmitted data for verifying error-free operation of the UART
TX/RX circuits.
Table 6.
Effect of DMA mode on state of RXRDY pin
Non-DMA mode
DMA mode
1 = FIFO empty
0-to-1 transition when FIFO empties
0 = at least 1 byte in FIFO
1-to-0 transition when FIFO reaches trigger level, or time-out occurs
Table 7.
Effect of DMA mode on state of TXRDY pin
Non-DMA mode
DMA mode
1 = at least 1 byte in FIFO
0-to-1 transition when FIFO becomes full
0 = FIFO empty
1-to-0 transition when FIFO has 1 empty space
相关PDF资料 |
PDF描述 |
|---|---|
| SC16C652BIB48,157 | IC ENCODER/DECODER IRDA 48LQFP |
| SC16C654BIBS,557 | IC QUAD UART 64BYTE 48HVQFN |
| SC16C750BIB64,151 | IC UART SINGLE W/FIFO 64-LQFP |
| SC16C752BIBS,157 | IC DUAL UART 64BYTE 32HVQFN |
| SC16C752IB48,128 | IC DUAL UART 64BYTE 48LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC16C650BIB48-F | 功能描述:UART 接口集成电路 16CB 2.5V-5V 1CH UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16C650BIBS | 功能描述:UART 接口集成电路 16CB 2.5V-5V 1CH UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16C650BIBS,128 | 功能描述:UART 接口集成电路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16C650BIBS,151 | 功能描述:UART 接口集成电路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC16C650BIBS,157 | 功能描述:UART 接口集成电路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。