参数资料
型号: SC16C754BIBM,151
厂商: NXP Semiconductors
文件页数: 11/50页
文件大小: 0K
描述: IC UART QUAD W/FIFO 64-LQFP
产品培训模块: Stand-Alone UARTs
标准包装: 250
通道数: 4,QUART
FIFO's: 64 字节
电源电压: 2.5V,3.3V,5V
带自动流量控制功能:
带故障启动位检测功能:
带调制解调器控制功能:
安装类型: 表面贴装
封装/外壳: 64-LQFP
供应商设备封装: 64-LQFP(7x7)
包装: 托盘
产品目录页面: 828 (CN2011-ZH PDF)
其它名称: 568-3290
935279069151
SC16C754BIBM-S
SC16C754B_4
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 04 — 6 October 2008
19 of 51
NXP Semiconductors
SC16C754B
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 64-byte FIFOs
6.8 Break and time-out conditions
An RX idle condition is detected when the receiver line, RX, has been HIGH for
4 character time. The receiver line is sampled midway through each bit.
When a break condition occurs, the TX line is pulled LOW. A break condition is activated
by setting LCR[6].
6.9 Programmable baud rate generator
The SC16C754B UART contains a programmable baud generator that takes any clock
input and divides it by a divisor in the range between 1 and (216
1). An additional
divide-by-4 prescaler is also available and can be selected by MCR[7], as shown in
Figure 13. The output frequency of the baud rate generator is 16
× the baud rate. The
formula for the divisor is given in Equation 1:
(1)
Where:
prescaler = 1, when MCR[7] is set to 0 after reset (divide-by-1 clock selected)
prescaler = 4, when MCR[7] is set to 1 after reset (divide-by-4 clock selected).
Remark: The default value of prescaler after reset is divide-by-1.
Figure 13 shows the internal prescaler and baud rate generator circuitry.
DLL and DLM must be written to in order to program the baud rate. DLL and DLM are the
least signicant and most signicant byte of the baud rate divisor. If DLL and DLM are
both zero, the UART is effectively disabled, as no baud clock will be generated.
Remark: The programmable baud rate generator is provided to select both the transmit
and receive clock rates.
Table 7 and Table 8 show the baud rate and divisor correlation for crystal with frequency
1.8432 MHz and 3.072 MHz, respectively.
Figure 14 shows the crystal clock circuit reference.
Fig 13. Prescaler and baud rate generator block diagram
divisor
XTAL1 crystal input frequency
prescaler
-------------------------------------------------------------------------------------
desired baud rate
16
×
()
------------------------------------------------------------------------------------------
=
BAUD RATE
GENERATOR
LOGIC
MCR[7] = 1
MCR[7] = 0
PRESCALER
LOGIC
(DIVIDE-BY-1)
INTERNAL
OSCILLATOR
LOGIC
002aaa233
XTAL1
XTAL2
input clock
PRESCALER
LOGIC
(DIVIDE-BY-4)
reference
clock
internal
baud rate
clock for
transmitter
and receiver
相关PDF资料
PDF描述
SC16C654BIBM,151 IC UART QUAD W/FIFO 64-LQFP
ATMEGA164A-CUR IC MCU AVR 16K 20MHZ 49VFBGA
SC16C554DBIB64,157 IC UART QUAD W/FIFO 64-LQFP
SC16C554DBIB64,151 IC UART QUAD W/FIFO 64-LQFP
SC16C554DBIB64,128 IC UART QUAD W/FIFO 64-LQFP
相关代理商/技术参数
参数描述
SC16C754BIBM-F 功能描述:UART 接口集成电路 16CB 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C754BIBM-S 功能描述:UART 接口集成电路 16CB 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C754IA68 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Quad UART with 64-byte FIFO
SC16C754IA68,512 功能描述:UART 接口集成电路 16C 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC16C754IA68,518 功能描述:UART 接口集成电路 16C 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel