- 您现在的位置：买卖IC网 > PDF目录14782 > SC189ZULTRT (Semtech)IC REG BUCK SYNC 3.3V 1.5A 6MLPQ PDF资料下载
参数资料
| 型号： | SC189ZULTRT |
| 厂商： | Semtech |
| 文件页数： | 16/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC 3.3V 1.5A 6MLPQ |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 3.3V |
| 输入电压： | 2.9 V ~ 5.5 V |
| PWM 型： | 电压模式 |
| 频率 - 开关： | 2.5MHz |
| 电流 - 输出： | 1.5A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-MLPD-UT |
| 包装： | 标准包装 |
| 供应商设备封装： | 6-MLPD-UT（2x2） |
| 产品目录页面： | 1357 (CN2011-ZH PDF) |
| 其它名称： | SC189ZULDKR |
SC189
Applications Information
?
?
?
?
R FB 1 [ k ? ] ? ( V OUT ? V OSTD )
DetailedDescription
The SC189 is a synchronous step-down pulse width
modulated (PWM) voltage mode DC-DC regulator
operating at 2.5MHz fixed-frequency. The switching
frequency is chosen to minimize the size of the external
inductor and capacitors while maintaining high
efficiency.
Operation
During normal operation, the internal high-
side PMOS device is activated on each ris-
ing edge of the internal oscillator. The voltage
feedback loop uses an internal feedback resistor divider.
The period is set by the on board oscillator when in PWM
mode at average to high loads. The device has an internal
low-side synchronous NMOS device and does not require a
Schottky diode on the LX pin. The device operates as a buck
converter in PWM mode with a fixed frequency of 2.5MHz.
Output Voltage Selection
The SC189 is designed for fixed output voltage. There
are some options for preset output voltage shown in
Table 1. If the voltage desired is not shown in the Table
1, it can be programmed via an external resistor di-
vider. There will be typical 1uA current flowing into the
VOUT pin. The typical schematic of adjustable output
voltage option from the part with standard 1.0V, the
SC189A, is shown in Figure 1. The C FF is needed for main-
tain the performance of the transient response. The
proper value of C FF can be calculated by the equation
( V OUT ? 0 . 5 ) 2 V OSTD
C FF [ nF ] = 10 × × ( )
V OSTD ? 0 . 5
,where the V OSTD is the standard voltage shown in Table 1.
shown above. For programming the output voltage from
other standard voltage, the R FB1 , R FB2 and C FF need to be
adjusted to meet the equation shown above.
Maximum Power Dissiption of SOT23-5 Package
The maximum power dissiption for junction tempera-
ture of less than 125°C on SOT23-5 package is shown
in figure 2. The curve is drawn based on the Θ JA of
90°C/W which is measured in free convection, mounted
on 10mm x 10mm, 2 layer FR4 PCB shown in figure 8
with copper of 1oz for each layer. The maximum power
dissiption may limit the maximum output current over
temperature. The figure 3 and figure 4 show the typi-
cal maximum output current for T J ≤ 125°C over tem-
perature of V IN =5.0V and V IN =3.3V, respectively. If using
inductor with higher loss (i.e., chip inductor), due to
the higher board temperature, the Θ JA will be a little bit
higher.
Protection Features
The SC189 provides the following protection features:
Thermal Shutdown
Current Limit
Over-Voltage Protection
Soft-Start Operation
Thermal Shutdown
The device has a thermal shutdown feature to protect
the SC189 if the junction temperature exceeds 160°C.
During thermal shutdown, the on-chip power devices
are disabled with the LX output floating. When the die
temperature drops by 10°C, the part will initiate a soft
start recovery to normal operation.
Figure 1 with a proper C FF calculated from the equation
To simplify the design, it is recommended to program the
voltage V OUT from 1.0V as V OUT indesired of
Schematic output Adjustable from standard SC189A (Std shown =1.0V) Current Limit
The internal PMOS power device in the switching stage is
protected by current limit feature. If the output is loaded
VIN
V LX V
C
C
R
R C
R FB 1 = ( V OUT ? 1 ) × R FB 2
R
10k ?
L
IN OUT
IN
OUT
EN GND
FB1 FF
Enable EN VOUT
FB2
SC189A
Figure 1 — Typical schematic for adjustable output
voltage option from standard 1.0V of SC189A
above the PMOS current limit for 32 consecutive cycles,
the SC189 enters foldback current limit mode and the
output current is limited to the current limit holding
current (I CL_HOLD ) of a few hundred milliampere. Under
these conditions the output voltage will be the product
of I CL_HOLD and the load resistance. The current limit
holding current (I CL_HOLD ) will be decreased when output
voltage is increased. The load presented must fall below
? 2009 Semtech =10k ? and C
Corp.
(2) R =10nF for standard design.
Note: (1) R EN is optional.
FB2 FF
16
www.semtech.com
相关PDF资料 |
PDF描述 |
|---|---|
| LGU1E153MELA | CAP ALUM 15000UF 25V 20% SNAP |
| MAX6426UK20+T | IC MPU/RESET CIRC 2.00V SOT23-5 |
| ECC30DRTI-S734 | CONN EDGECARD 60POS DIP .100 SLD |
| ECA22DRST-S288 | CONN EDGECARD 44POS .125 EXTEND |
| V72C28T150B2 | CONVERTER MOD DC/DC 28V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC18IM700 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Master I2C-bus controller with UART interface |
| SC18IM700IPW | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Master I-2C - bus controller with UART interface |
| SC18IM700IPW,112 | 功能描述:UART 接口集成电路 CTRL I2C W/UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC18IM700IPW,128 | 功能描述:UART 接口集成电路 UART-MASTER I2C RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC18IM700IPW/S8HP | 功能描述:IC CTRL I2CW/UART 16TSSOP 制造商:nxp usa inc. 系列:- 零件状态:在售 协议:I2C 功能:控制器 接口:UART 标准:- 电压 - 电源:2.4 V ~ 3.6 V 电流 - 电源:9mA 工作温度:-40°C ~ 85°C 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商器件封装:16-TSSOP 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。