参数资料
型号: SC28L92A1B,528
厂商: NXP Semiconductors
文件页数: 20/73页
文件大小: 0K
描述: IC UART DUAL W/FIFO 44PQFP
标准包装: 1,500
系列: IMPACT
特点: 故障启动位检测
通道数: 2,DUART
FIFO's: 16 字节
电源电压: 3.3V,5V
带自动流量控制功能:
带故障启动位检测功能:
带调制解调器控制功能:
带CMOS:
安装类型: 表面贴装
封装/外壳: 44-QFP
供应商设备封装: 44-PQFP(10x10)
包装: 带卷 (TR)
其它名称: 935263294528
SC28L92A1B-T
SC28L92A1B-T-ND
27
2552K–AVR–04/11
ATmega329/3290/649/6490
8.1.4
Asynchronous Timer Clock – clk
ASY
The Asynchronous Timer clock allows the Asynchronous Timer/Counter and the LCD controller
to be clocked directly from an external clock or an external 32kHz clock crystal. The dedicated
clock domain allows using this Timer/Counter as a real-time counter even when the device is in
sleep mode. It also allows the LCD controller output to continue while the rest of the device is in
sleep mode.
ADC Clock – clk
ADC
The ADC is provided with a dedicated clock domain. This allows halting the CPU and I/O clocks
in order to reduce noise generated by digital circuitry. This gives more accurate ADC conversion
results.
8.2
Clock Sources
The device has the following clock source options, selectable by Flash Fuse bits as shown
below. The clock from the selected source is input to the AVR clock generator, and routed to the
appropriate modules.
Note:
1. For all fuses “1” means unprogrammed while “0” means programmed.
The various choices for each clocking option is given in the following sections. When the CPU
wakes up from Power-down or Power-save, the selected clock source is used to time the start-
up, ensuring stable Oscillator operation before instruction execution starts. When the CPU starts
from reset, there is an additional delay allowing the power to reach a stable level before com-
mencing normal operation. The Watchdog Oscillator is used for timing this real-time part of the
start-up time. The number of WDT Oscillator cycles used for each time-out is shown in Table 8-
2. The frequency of the Watchdog Oscillator is voltage dependent as shown in “Typical Charac-
8.2.1
Default Clock Source
The device is shipped with CKSEL = “0010”, SUT = “10”, and CKDIV8 programmed. The default
clock source setting is the Internal RC Oscillator with longest start-up time and an initial system
clock prescaling of 8. This default setting ensures that all users can make their desired clock
source setting using an In-System or Parallel programmer.
Table 8-1.
Device Clocking Options Select
Device Clocking Option
CKSEL3..0
External Crystal/Ceramic Resonator
1111 - 1000
External Low-frequency Crystal
0111 - 0110
Calibrated Internal RC Oscillator
0010
External Clock
0000
Reserved
0011, 0001, 0101, 0100
Table 8-2.
Number of Watchdog Oscillator Cycles
Typ Time-out (V
CC = 5.0V)
Typ Time-out (V
CC = 3.0V)
Number of Cycles
4.1ms
4.3ms
4K (4,096)
65ms
69ms
64K (65,536)
相关PDF资料
PDF描述
D38999/20JC98PA CONN RCPT 10POS WALL MNT W/PINS
SCC2692AC1B44,551 IC UART DUAL W/FIFO 44PQFP
MS3114E12-10SW CONN RCPT 10POS JAM NUT W/SCKT
SCC68681E1N40,112 IC DUART 40DIP
MS3114E12-10S CONN RCPT 10POS JAM NUT W/SCKT
相关代理商/技术参数
参数描述
SC28L92A1B557 制造商:NXP Semiconductors 功能描述:IC UART W/FIFO DUAL 44PQFP 制造商:NXP Semiconductors 功能描述:IC DUAL UART FIFO 1MBPS 5.
SC28L92A1BS 功能描述:UART 接口集成电路 3V-5V 1CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC28L92A1BS,528 功能描述:UART 接口集成电路 3V-5V 1CH UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC28L92A1BS,551 功能描述:UART 接口集成电路 3V-5V 1CH UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC28L92A1BS,557 功能描述:UART 接口集成电路 3V-5V 1CH UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel