参数资料
型号: SC28L92A1B,528
厂商: NXP Semiconductors
文件页数: 36/73页
文件大小: 0K
描述: IC UART DUAL W/FIFO 44PQFP
标准包装: 1,500
系列: IMPACT
特点: 故障启动位检测
通道数: 2,DUART
FIFO's: 16 字节
电源电压: 3.3V,5V
带自动流量控制功能:
带故障启动位检测功能:
带调制解调器控制功能:
带CMOS:
安装类型: 表面贴装
封装/外壳: 44-QFP
供应商设备封装: 44-PQFP(10x10)
包装: 带卷 (TR)
其它名称: 935263294528
SC28L92A1B-T
SC28L92A1B-T-ND
41
2552K–AVR–04/11
ATmega329/3290/649/6490
10. System Control and Reset
10.1
Resetting the AVR
During reset, all I/O Registers are set to their initial values, and the program starts execution
from the Reset Vector. The instruction placed at the Reset Vector must be a JMP – Absolute
Jump – instruction to the reset handling routine. If the program never enables an interrupt
source, the Interrupt Vectors are not used, and regular program code can be placed at these
locations. This is also the case if the Reset Vector is in the Application section while the Interrupt
Vectors are in the Boot section or vice versa. The circuit diagram in Figure 10-1 shows the reset
logic. “System and Reset Characteristics” on page 330 defines the electrical parameters of the
reset circuitry.
The I/O ports of the AVR are immediately reset to their initial state when a reset source goes
active. This does not require any clock source to be running.
After all reset sources have gone inactive, a delay counter is invoked, stretching the internal
reset. This allows the power to reach a stable level before normal operation starts. The time-out
period of the delay counter is defined by the user through the SUT and CKSEL Fuses. The dif-
ferent selections for the delay period are presented in “Clock Sources” on page 27.
10.2
Reset Sources
The ATmega329/3290/649/6490 has five sources of reset:
Power-on Reset. The MCU is reset when the supply voltage is below the Power-on Reset
threshold (V
POT).
External Reset. The MCU is reset when a low level is present on the RESET pin for longer
than the minimum pulse length.
Watchdog Reset. The MCU is reset when the Watchdog Timer period expires and the
Watchdog is enabled.
Brown-out Reset. The MCU is reset when the supply voltage V
CC is below the Brown-out
Reset threshold (V
BOT) and the Brown-out Detector is enabled.
JTAG AVR Reset. The MCU is reset as long as there is a logic one in the Reset Register,
one of the scan chains of the JTAG system. Refer to the section “IEEE 1149.1 (JTAG)
相关PDF资料
PDF描述
D38999/20JC98PA CONN RCPT 10POS WALL MNT W/PINS
SCC2692AC1B44,551 IC UART DUAL W/FIFO 44PQFP
MS3114E12-10SW CONN RCPT 10POS JAM NUT W/SCKT
SCC68681E1N40,112 IC DUART 40DIP
MS3114E12-10S CONN RCPT 10POS JAM NUT W/SCKT
相关代理商/技术参数
参数描述
SC28L92A1B557 制造商:NXP Semiconductors 功能描述:IC UART W/FIFO DUAL 44PQFP 制造商:NXP Semiconductors 功能描述:IC DUAL UART FIFO 1MBPS 5.
SC28L92A1BS 功能描述:UART 接口集成电路 3V-5V 1CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC28L92A1BS,528 功能描述:UART 接口集成电路 3V-5V 1CH UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC28L92A1BS,551 功能描述:UART 接口集成电路 3V-5V 1CH UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
SC28L92A1BS,557 功能描述:UART 接口集成电路 3V-5V 1CH UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel