- 您现在的位置：买卖IC网 > PDF目录11820 > SC28L92A1BS,551 (NXP Semiconductors)IC UART DUAL W/FIFO 44PQFP PDF资料下载
参数资料
| 型号： | SC28L92A1BS,551 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 6/73页 |
| 文件大小： | 0K |
| 描述： | IC UART DUAL W/FIFO 44PQFP |
| 标准包装： | 490 |
| 系列： | IMPACT |
| 特点： | 故障启动位检测 |
| 通道数： | 2，DUART |
| FIFO's： | 16 字节 |
| 电源电压： | 3.3V，5V |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 供应商设备封装： | 48-HVQFN EP（6x6） |
| 包装： | 托盘 |
| 其它名称： | 935281063551 SC28L92A1BS-S SC28L92A1BS-S-ND |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页
14
2552K–AVR–04/11
ATmega329/3290/649/6490
6.5.1
The X-register, Y-register, and Z-register
The registers R26..R31 have some added functions to their general purpose usage. These reg-
isters are 16-bit address pointers for indirect addressing of the data space. The three indirect
address registers X, Y, and Z are defined as described in Figure 6-3.
Figure 6-3.
The X-, Y-, and Z-registers
In the different addressing modes these address registers have functions as fixed displacement,
automatic increment, and automatic decrement (see the instruction set reference for details).
6.6
Stack Pointer
The Stack is mainly used for storing temporary data, for storing local variables and for storing
return addresses after interrupts and subroutine calls. The Stack Pointer Register always points
to the top of the Stack. Note that the Stack is implemented as growing from higher memory loca-
tions to lower memory locations. This implies that a Stack PUSH command decreases the Stack
Pointer.
The Stack Pointer points to the data SRAM Stack area where the Subroutine and Interrupt
Stacks are located. This Stack space in the data SRAM must be defined by the program before
any subroutine calls are executed or interrupts are enabled. The Stack Pointer must be set to
point above 0x60. The Stack Pointer is decremented by one when data is pushed onto the Stack
with the PUSH instruction, and it is decremented by two when the return address is pushed onto
the Stack with subroutine call or interrupt. The Stack Pointer is incremented by one when data is
popped from the Stack with the POP instruction, and it is incremented by two when data is
popped from the Stack with return from subroutine RET or return from interrupt RETI.
The AVR Stack Pointer is implemented as two 8-bit registers in the I/O space. The number of
bits actually used is implementation dependent. Note that the data space in some implementa-
tions of the AVR architecture is so small that only SPL is needed. In this case, the SPH Register
will not be present.
15
XH
XL
0
X-register
70
7
0
R27 (0x1B)
R26 (0x1A)
15
YH
YL
0
Y-register
70
7
0
R29 (0x1D)
R28 (0x1C)
15
ZH
ZL
0
Z-register
70
7
0
R31 (0x1F)
R30 (0x1E)
Bit
151413
1211
10
9
8
SP15
SP14
SP13
SP12
SP11
SP10
SP9
SP8
SPH
SP7
SP6
SP5
SP4
SP3
SP2
SP1
SP0
SPL
765
432
10
Read/Write
R/W
Initial Value
0
000
00
相关PDF资料 |
PDF描述 |
|---|---|
| MS3116E14-15S | CONN PLUG 15POS STRAIGHT W/SCKT |
| SCC2692AE1N28,602 | IC DUART 28-DIP |
| SCC68692E1N40,602 | IC DUART 40DIP |
| SCC2692AE1N40,602 | IC DUART 40-DIP |
| SC16C654BIEC,551 | IC UART QUAD W/FIFO 64-LFBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC28L92A1BS-F | 功能描述:UART 接口集成电路 3V-5V 1CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC28L92A1BS-S | 功能描述:UART 接口集成电路 3V-5V 1CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC28P-1GREEN | 制造商:Thomas & Betts 功能描述:ID TAG GREEN |
| SC28P-1RED | 制造商:Thomas & Betts 功能描述:ID TAG RED |
| SC28P-1YELLOW | 制造商:Thomas & Betts 功能描述:ID TAG YELLOW |
发布紧急采购，3分钟左右您将得到回复。