- 您现在的位置：买卖IC网 > PDF目录11824 > SCC68681C1A44,518 (NXP Semiconductors)IC DUART 44PLCC PDF资料下载
参数资料
| 型号： | SCC68681C1A44,518 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 26/29页 |
| 文件大小： | 0K |
| 描述： | IC DUART 44PLCC |
| 标准包装： | 500 |
| 特点： | 故障启动位检测 |
| 通道数： | 2，DUART |
| FIFO's： | 3 位 |
| 电源电压： | 5V |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LCC（J 形引线） |
| 供应商设备封装： | 44-PLCC |
| 包装： | 带卷 (TR) |
| 其它名称： | 935274497518 SCC68681C1A44-T SCC68681C1A44-T-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页
Philips Semiconductors
Product data
SCC68681
Dual asynchronous receiver/transmitter (DUART)
2004 Apr 06
6
BLOCK DIAGRAM
The SCC68681 DUART consists of the following eight major
sections: data bus buffer, operation control, interrupt control, timing,
communications Channels A and B, input port and output port. Refer
to Figure 2, ‘Block Diagram’.
Data Bus Buffer
The data bus buffer provides the interface between the external and
internal data buses. It is controlled by the operation control block to
allow read and write operations to take place between the controlling
CPU and the DUART.
Operation Control
The operation control logic receives operation commands from the
CPU and generates appropriate signals to internal sections to
control device operation. It contains address decoding and read and
write circuits to permit communications with the microprocessor via
the data bus buffer. The DTACKN output is asserted during write
and read cycles to indicate to the CPU that data has been latched
on a write cycle, or that valid data is present on the bus on a read
cycle.
Interrupt Control
A single active-LOW interrupt output (INTRN) is provided which is
activated upon the occurrence of any of eight internal events.
Associated with the interrupt system are the Interrupt Mask Register
(IMR) and the Interrupt Status Register (ISR), the Auditory Control
Register(ACR) and the Interrupt Vector Register (IVR). The IMR
may be programmed to select only certain conditions to cause
INTRN to be asserted. The ISR can be read by the CPU to
determine all currently active interrupting conditions. When IACKN is
asserted, and the DUART has an interrupt pending, the DUART
responds by placing the contents of the IVR register on the data bus
and asserting DTACKN.
Outputs OP3–OP7 can be programmed to provide discrete interrupt
outputs for the transmitter, receivers, and counter/timer.
Timing Circuits
The timing block consists of a crystal oscillator, a baud rate
generator, a programmable 16-bit counter/timer, and four clock
selectors. The crystal oscillator operates directly from a crystal
connected across the X1/CLK and X2 inputs. If an external clock of
the appropriate frequency is available, it may be connected to
X1/CLK. The clock serves as the basic timing reference for the Baud
Rate Generator (BRG), the counter/timer, and other internal circuits.
A clock signal within the limits specified in the specifications section
of this data sheet must always be supplied to the DUART. If an
external is used instead of a crystal, X1 should be driven using a
configuration similar to the one in Figure 8.
The baud rate generator operates from the oscillator or external
clock input and is capable of generating 18 commonly used data
communications baud rates ranging from 50 to 115.2 k baud. The
clock outputs from the BRG are at 16
× the actual baud rate. The
counter/timer can be used as a timer to produce a 16
× clock for any
other baud rate by counting down the crystal clock or an external
clock. The four clock selectors allow the independent selection, for
each receiver and transmitter, of any of these baud rates or external
timing signal.
Counter/Timer (C/T)
The counter timer is a 16 bit programmable divider that operates
one of three modes: Counter, Timer or Time Out mode. In all three
modes it uses the 16-bit value loaded to the CTUR and CTLR
registers. (Counter timer upper and lower preset registers).
In the timer mode it generates a square wave.
In the counter mode it generates a time delay.
In the time out mode it monitors the receiver data flow and signals
data flow has paused. In the time out mode the receiver controls
the starting/stopping of the C/T.
The counter operates as a down counter and sets its output bit in
the ISR (Interrupt Status Register) each time it passes through 0.
The output of the counter/timer may be seen on one of the OP pins
or as an Rx or Tx clock.
The Timer/Counter is controlled with six (6) ‘commands’; Start C/T,
Stop C/T, write C/T, preset registers, read C/T value, set or reset
time out mode.
Please see the detail of the commands under the Counter/Timer
register descriptions.
Communications Channels A and B
Each communications channel of the SCC68681 comprises a
full-duplex asynchronous receiver/transmitter (DUART). The
operating frequency for each receiver and transmitter can be
selected independently from the baud rate generator, the counter
timer, or from an external input.
The transmitter accepts parallel data from the CPU, converts it to a
serial bit stream, inserts the appropriate start, stop, and optional
parity bits and outputs a composite serial stream of data on the TxD
output pin. The receiver accepts serial data on the RxD pin,
converts this serial input to parallel format, checks for start bit, stop
bit, parity bit (if any), or break condition and sends an assembled
character to the CPU.
The input port pulse detection circuitry uses a 38.4 kHz sampling
clock derived from one of the baud rate generator taps. This results
in a sampling period of slightly more than 25
s (assuming that the
clock input is 3.6864 MHz). The detection circuitry, in order to
guarantee a true change in level has occurred, requires that two
successive samples at the new logic level be observed. As a
consequence, the minimum duration of the signal change is 25
s if
the transition occurs coincident with the first sample pulse. The
50
s time refers to the situation in which the change of state is just
missed and the first change of state is not detected until 25
s later.
Input Port
The inputs to this unlatched 6-bit port can be read by the CPU by
performing a read operation at address 0xD. A HIGH input results in
a logic ‘1’ while a LOW input results in a logic ‘0’. D7 will always
read as a logic ‘1’ and D6 will reflect the level of IACKN. The pins of
this port can also serve as auxiliary inputs to certain portions of the
DUART logic.
Four change-of-state detectors are provided which are associated
with inputs IP3, IP2, IP1 and IP0. A HIGH-to-LOW or LOW-to-HIGH
transition of these inputs, lasting longer than 25 to 50
s, will set the
corresponding bit in the input port change register. The bits are
cleared when the register is read by the CPU. Any change-of-state
can also be programmed to generate an interrupt to the CPU.
All the IP pins have a small pull-up device that will source 1 to 4
A
of current from VCC. These pins do not require pull-up devices or
VCC connections if they are not used.
Output Port
The 8-bit multipurpose output port can be used as a general
purpose output port, in which case the outputs are the complements
of the Output Port Register (OPR). OPR[n] = 1 results in
OP[n] = LOW and vice versa. Bits of the OPR can be individually set
and reset. A bit is set by performing a write operation at address
0xE with the accompanying data specifying the bits to be reset
(1 = set, 0 = no change). Likewise, a bit is reset by a write at
相关PDF资料 |
PDF描述 |
|---|---|
| VE-BTN-IW-F3 | CONVERTER MOD DC/DC 18.5V 100W |
| VI-26J-IY | CONVERTER MOD DC/DC 36V 50W |
| MS27484E10B99P | CONN PLUG 7POS STRAIGHT W/PINS |
| VE-BTN-IW-F1 | CONVERTER MOD DC/DC 18.5V 100W |
| SC28L91A1A,512 | IC UART SINGLE W/FIFO 44-PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SCC68681C1A44-T | 功能描述:UART 接口集成电路 RPLCMNT FOR SCN68681 RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SCC68681C1N40 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Dual asynchronous receiver/transmitter |
| SCC68681C1N40,112 | 功能描述:UART 接口集成电路 2CH.UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SCC68681C1N40112 | 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述: |
| SCC68681E1A44 | 功能描述:UART 接口集成电路 RPLCMNT FOR SCN68681 RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。