- 您现在的位置：买卖IC网 > PDF目录21883 > SFCA8192H1BR4TO-I-DT-236-STD (Swissbit NA Inc)FLASH CFAST UDMA/MDMA/PIO 8GB PDF资料下载
参数资料
| 型号： | SFCA8192H1BR4TO-I-DT-236-STD |
| 厂商： | Swissbit NA Inc |
| 文件页数： | 11/51页 |
| 文件大小： | 0K |
| 描述： | FLASH CFAST UDMA/MDMA/PIO 8GB |
| 标准包装： | 20 |
| 系列： | F-100 |
| 存储容量： | 8GB |
| 存储器类型： | 存储卡 - CFast? |
| 其它名称： | 1052-1080 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
5.3 Card detection with CDI and CDO pin
As specified in the CFAST specification 1.0 the CDI is
connected to a controller input pin.
If V_CDI is more than 0.6V larger than Vcc a current flows
through the internal ESD diode and supplies the
controller with an undefined voltage.
For better card detection all CFAST cards produced after
January 2011 have CDI connected with CDO.
5.3.1 Positive card detection
Without CDI-CDO connection V_CDO is about 1.0 V for
R_i=100…400 Ohm.
With the new CDI-CDO connection for a serial resistance
R_i=50 to 400 Ohm V_CDO is between 2.1 and 1.5V.
If Vcc pins are not connected R_i should not be smaller
than 50 Ohms because the current via the CDI pin and
the diodes increases and the internal controller
structures could be damaged.
Recommendations
If a voltage switch/regulator with a positive enable
CE pin with the circuit above is used, the enable pin
should detect a max high level threshold
V_High,min=0.8V for the old and
V_High,min=1.2…1.8V depending on R_i (see diagram).
To limit the CDI current below 7 mA and have a
significant voltage V_CDO, R_i should be between 200
and 400 Ohm
R_o should be a weak pull down resistor (~100kOhm)
to prevent a floating ENABLE signal, depending on
input properties of the switch/regulator.
To prevent current through the CDI pin (if
V_CDI>Vcc+0.6V) Vcc should be always connected to the host connector.
If there is no reason, Vcc could always be connected to 3.3V.
5.3.2 Inverted card detection
If a voltage switch/regulator with a negative enable – CE pin is used, R_o should be weakly pulled up and CDI
should pulled down to ground. So CDO is low, if a card is plugged in and the pull up current through the CDI/CDO
lines is limited. If the card controller detects a low level at CDI, it switches CDO completely to ground after 0.4s.
This card detection only work with the new cards with connected CDI/CDO (if no Vcc is applied). With applied Vcc
it also works with the old cards.
5.3.3 Alternative card detection
Alternatively a ground pin of the host connector (e.g. PC2) could be used as card detection. This pin should be
pulled up weakly. If a card is inserted it will be connected to ground.
Swissbit AG
Industriestrasse 4
Swissbit reserves the right to change products or specifications without notice.
Revision: 1.41
CH-9552 Bronschhofen
Switzerland
www.swissbit.com
industrial@swissbit.com
F-100_data_sheet_CA-HxBR_Rev141.doc
Page 11 of 51
相关PDF资料 |
PDF描述 |
|---|---|
| MX3AWT-A1-0000-000B51 | LED XLAMP COOL WHITE 6500K 2PLCC |
| MX3AWT-A1-R250-0008F7 | LED XLAMP WHITE 350MA 2PLCC |
| MX3AWT-A1-R250-0008F6 | LED XLAMP WHITE 350MA 2PLCC |
| SFCF32GBH2BU4TO-I-QT-517-STD | FLASH SLC UDMA/MDMA/PIO 32GB |
| MX3AWT-A1-R250-0008E7 | LED XLAMP WHITE 350MA 2PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SFCA8192H2BV4TO-C-DT-216-STD | 制造商:SWISSBIT NA INC 功能描述:FLASH |
| SFCA8192H2BV4TO-C-DT-226-STD | 制造商:SWISSBIT 功能描述:CFAST F-240 DENSITY COMMERCIAL - Trays |
| SFCA8192H2BV4TO-I-DT-216-STD | 功能描述:FLASH CFAST UDMA/MDMA/PIO 8GB RoHS:是 类别:存储卡，模块 >> 存储器，PC 卡 系列:F-240 标准包装:30 系列:- 存储容量:8GB 存储器类型:存储卡 - Extreme III SD? |
| SFCA8192H2BV4TO-I-DT-226-STD | 制造商:SWISSBIT 功能描述:CFAST F-240 DENSITY INDUSTRIAL - Trays |
| SFCC-4-01 | 功能描述:CABLE CLAMP SPLIT FLAT #4 SCREW RoHS:是 类别:线缆，导线 - 管理 >> 线夹和夹具 系列:- 标准包装:100 系列:TC 类型:C-夹 开口尺寸:0.79" L x 0.54" W x 0.67" H（20.1mm x 13.7mm x 17.0mm） 安装类型:钉子 材质:聚丙烯 颜色:黑 |
发布紧急采购，3分钟左右您将得到回复。