- 您现在的位置：买卖IC网 > PDF目录21887 > SFSD0512N1BN1TO-I-ME-151-STD (Swissbit NA Inc)FLASH MICRO SD 512MB IND TEMP PDF资料下载
参数资料
| 型号： | SFSD0512N1BN1TO-I-ME-151-STD |
| 厂商： | Swissbit NA Inc |
| 文件页数： | 13/23页 |
| 文件大小： | 0K |
| 描述： | FLASH MICRO SD 512MB IND TEMP |
| RoHS指令信息： | Environment Protection Declaration |
| 标准包装： | 1 |
| 系列： | S-200u |
| 存储容量： | 512MB |
| 存储器类型： | 存储卡 - microSD? |
| 其它名称： | 1052-1060 |
7.1.2 SPI Bus Mode Protocol
The Serial Parallel Interface (SPI) Bus is a general purpose synchronous serial interface. The SPI mode consists of a
secondary communication protocol. The interface is selected during the first reset command after power up
(CMD0) and it cannot be changed once the card is powered on.
While the SD channel is based on command and data bit streams which are initiated by a start bit and
terminated by a stop bit, the SPI channel is byte oriented. Every command or data block is built of 8-bit bytes
and is byte aligned to the CS signal.
The card identification and addressing methods are replaced by a hardware Chip Select (CS) signal. There are no
broadcast commands. For every command, a card (slave) is selected by asserting (active low) the CS signal.
The CS signal must be continuously active for the duration of the SPI transaction (command, response and data).
The only exception occurs during card programming, when the host can de-assert the CS signal without affecting
the programming process.
The bidirectional CMD and DAT lines are replaced by unidirectional dataIn and dataOut signals.
Table 19: SPI Bus Signals
Signal
/CS
CLK
Data In
Data Out
Vdd, Vss
Description
Host to card chip select
Host to card clock signal
Host to card data signal
Card to host data signal
Power and ground
Figure 10: SPI bus topology
7.1.3 Mode Selection
The SD Memory Card wakes up in the SD mode. It will enter SPI mode if the CS signal is asserted (negative) during
the reception of the reset command (CMD0) and the card is in idle_state . If the card recognizes that the SD mode
is required it will not respond to the command and remain in the SD mode.
If SPI mode is required the card will switch to SPI and respond with the SPI mode R1 response.
The only way to return to the SD mode is by entering the power cycle. In SPI mode the SD Memory Card protocol
state machine is not observed. All the SD Memory Card commands supported in SPI mode are always available.
During the initialization sequence, if the host gets Illegal Command indication for ACMD41 sent to the card, it may
assume that the card is Multimedia Card. In that case it should re-start the card as Multimedia Card using CMD0
and CMD1.
Swissbit AG
Industriestrasse 4
Swissbit reserves the right to change products or specifications without notice.
Revision: 1.00
CH-9552 Bronschhofen
Switzerland
www.swissbit.com
info@swissbit.com
S-200u_data_sheet_SD-NxBN_Rev102
Page 13 of 23
相关PDF资料 |
PDF描述 |
|---|---|
| DK311 | LCD DPM +9V 200MV 3.5 DIGIT +GRN |
| Q2-Z-QK2-01-6IN-82 | HEATSHRINK KIT 6" 5/16"-1" 82PC |
| MLEAWT-A1-0000-0002A2 | LED XLAMP NEUTRAL WHIT 4750K SMD |
| MLEAWT-A1-0000-0002A1 | LED XLAMP ML-E WHITE SMD |
| MLEAWT-A1-0000-0002F6 | LED XLAMP NEUTRAL WHIT 3750K SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SFSD0512N1BN1TO-I-ME-161-STD | 制造商:Swissbit 功能描述:Memory Cards 512MB IND MICRO SD SLC FLASH S200u |
| SFSD-05-28C-G-36.00-SR | 制造商:Samtec Inc 功能描述:.050 SOCKET DISCRETE CABLE ASSEMBLY - Bulk |
| SFSD-05-28C-G-40.00-S | 制造商:Samtec Inc 功能描述:.050 SOCKET DISCRETE CABLE ASSEMBLY - Bulk |
| SFSD-05-28C-G-40.00-SR | 制造商:Samtec Inc 功能描述:.050 SOCKET DISCRETE CABLE ASSEMBLY - Bulk |
| SFSD-05-28C-G-96.00-SR | 制造商:Samtec Inc 功能描述:.050 SOCKET DISCRETE CABLE ASSEMBLY - Bulk |
发布紧急采购，3分钟左右您将得到回复。