- 您现在的位置：买卖IC网 > PDF目录10907 > SI2434-D-GT (Silicon Laboratories Inc)IC ISOMODEM GLOBAL DAA 24TSSOP PDF资料下载
参数资料
| 型号： | SI2434-D-GT |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 10/60页 |
| 文件大小： | 0K |
| 描述： | IC ISOMODEM GLOBAL DAA 24TSSOP |
| 标准包装： | 62 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
Si2457/34/15/04
18
Rev. 1.3
4.2. Command Mode
Upon reset, the ISOmodem is in command mode and
accepts “AT” commands. An outgoing modem call can
be made using the “ATDT#” (tone dial) or “ATDP#”
(pulse dial) command after the device is configured. If
the handshake is successful, the modem responds with
the response codes detailed in Table 12 on page 38 and
enters data mode.
4.3. Data Mode
The Si2457/34/15/04 ISOmodem is in data mode while
it has a telephone line connection to another modem or
is in the process of establishing a connection.
Data protocols are available to provide error correction
to improve reliability (V.42 and MNP2-4) and data
compression to increase throughput (V.44, V.42bis and
MNP5).
Each connection between two modems in data mode
begins with a handshaking sequence. During this
sequence, the modems determine the line speed, data
protocol, and related parameters for the data link.
Configuration through AT commands determines the
range of choices available to the modem during the
negotiation process.
4.4. Fast Connect
The Si2457/34/15/04 supports a fast connect mode of
operation to reduce the time of a connect sequence in
originate mode. The Fast Connect modes can be
enabled for V.21, V.22, Bell103, and V.29 modulations.
See AN93 for details.
4.5. V.80 Synchronous Access Mode
The Si2457/34/15/04 supports a V.80 synchronous
access mode of operation, which operates with an
asynchronous DTE and a synchronous DCE. See
“AN93: ISOmodem Chipset Family Designer's Guide”.
4.6. Clocking
The Si2457/34/15/04 contains an on-chip phase-locked
loop (PLL) and clock generator to derive all necessary
internal system clocks from a single clock input. A
32.768 kHz or 4.9152 MHz crystal can be used across
XTALI and XTALO pins to form the master clock
(±100 ppm max, ±25 ppm recommended) for the
ISOmodem. The 32.768 kHz option can provide lower
BOM costs and smaller footprint. Alternatively, a clock
input of 27 MHz, 4.9152 MHz, or 32.768 kHz can be
provided to XTALI if that clock source is available in the
system. A 4.9152 MHz clock input is the default clock
option.
Other clock options are selected at power-up
through reset strapping. Refer to AN93 for details.
4.7. Low-Power Modes
The Si2457/34/15/04 provides multiple low power
modes. Using the S24 S-register, the Si2457/34/15/04
can be set to automatically enter sleep mode after a
pre-programmed time of inactivity with either the DTE or
the remote modem. The sleep mode is entered after
(S24) seconds have passed since the last DTE activity,
after the transmit FIFO is empty, and after the last data
are received from the remote modem.
Additionally, the Si2457/34/15/04 can be placed in
wake-on-ring-mode using the command, AT&Z. In either
mode, the ISOmodem remains in the sleep state until
one of the following occurs:
A 1-to-0 transition on TXD (UART mode).
A 1-to-0 transition on SS (SPI mode).
A 1-to-0 transition on CS (parallel mode).
An incoming ring is detected.
A parallel telephone is picked up.
Line polarity reversal
The Si2457/34/15/04 may also be placed in a complete
powerdown
mode.
Once
the
Si2457/34/15/04
completely powers down, it can only be powered back
on via the RESET pin.
4.8. Data Compression
The modem can achieve DTE (host-to-ISOmodem)
speeds greater than the maximum DCE (modem-to-
modem) speed through the use of a data compression
protocol. The compression protocols available are the
ITU-T V.42bis and MNP5 protocols. Data compression
attempts to increase throughput by compressing the
data before actually sending it. Thus, the modem is able
to transmit more data in a given period of time.
4.9. Error Correction
The Si2457/34/15/04 ISOmodem can employ error
correction (reliable) protocols to ensure error-free
delivery of asynchronous data sent between the host
and the remote end. The Si2457/34/15/04 supports V.42
and MNP2-4 error correction protocols. V.42 (LAPM) is
most commonly used and is enabled by default.
4.10. Wire Mode
Wire mode is used to communicate with standard non-
error correcting modems. When optioned with \N3, the
Si2457/34/15/04 falls back to wire mode if it fails in an
attempt to negotiate a V.42 link with the remote modem.
Error correction and data compression are not active in
wire mode.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-260-CV | CONVERTER MOD DC/DC 5V 150W |
| VI-2N3-IX-F4 | CONVERTER MOD DC/DC 24V 75W |
| VI-25H-CV | CONVERTER MOD DC/DC 52V 150W |
| VI-25F-CV | CONVERTER MOD DC/DC 72V 150W |
| VI-25D-CV | CONVERTER MOD DC/DC 85V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI2434-D-GTR | 制造商:Silicon Laboratories Inc 功能描述:Modem Chip Chipset 24-Pin TSSOP T/R 制造商:Silicon Laboratories Inc 功能描述:33.6 KBPS ISOMODEM SYSTEM-SIDE - LEAD-FREE - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:IC ISOMODEM GLOBAL DAA 24TSSOP 制造商:Silicon Laboratories Inc 功能描述:33.6 kbps ISOmodem System-Side PBF |
| Si2434FS08-EVB | 功能描述:网络开发工具 16-pin Si2434 + Si3008 ISOmodem Evaluation Board RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
| Si2434FS18-EVB | 功能描述:网络开发工具 16-pin Si2434 + Si3018 ISOmodem Evaluation Board RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
| SI2434-FT | 功能描述:电信线路管理 IC CONTACT SILICON LABS FOR AVAILABILITY RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI2434-FT/REV B | 制造商:Silicon Laboratories Inc 功能描述:LEAD FREE ISO MODEM - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。