- 您现在的位置：买卖IC网 > PDF目录18780 > SI4736-C40-GM (Silicon Laboratories Inc)IC RX AM/FM/WB RADIO 20UQFN PDF资料下载
参数资料
| 型号： | SI4736-C40-GM |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 25/42页 |
| 文件大小： | 0K |
| 描述： | IC RX AM/FM/WB RADIO 20UQFN |
| 标准包装： | 490 |
| 频率： | 520kHz ~ 1.71MHz，64MHz ~ 108MHz，162.4MHz ~ 162.55MHz |
| 调制或协议： | AM，FM，WB |
| 应用： | 通用 |
| 电流 - 接收： | 19.9mA |
| 数据接口： | PCB，表面贴装 |
| 天线连接器： | PCB，表面贴装 |
| 特点： | 配有 RSSI |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -20°C ~ 85°C |
| 封装/外壳： | 20-UFQFN 裸露焊盘 |
| 供应商设备封装： | 20-QFN（3x3） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
Si4736/37/38/39-C40
For read operations, after the Si4736/37/38/39 has
acknowledged the control byte, it will drive an 8-bit data
byte on SDIO, changing the state of SDIO on the falling
edge of SCLK. The user acknowledges each data byte
by driving SDIO low for one cycle, on the next falling
edge of SCLK. If a data byte is not acknowledged, the
transaction will end. The user may read up to 16 data
bytes in a single 2-wire transaction. These bytes contain
the response data from the Si4736/37/38/39.
A 2-wire transaction ends with the STOP condition,
which occurs when SDIO rises while SCLK is high.
For details on timing specifications and diagrams, refer
to Table 5, “2-Wire Control Interface Characteristics” on
5.15.3. SPI Control Interface Mode
When selecting SPI mode, the user must ensure that a
rising edge of SCLK does not occur within 300 ns
before the rising edge of RST.
SPI bus mode uses the SCLK, SDIO, and SEN pins for
read/write operations. The system controller can
choose to receive read data from the device on either
SDIO or GPO1. A transaction begins when the system
controller drives SEN = 0. The system controller then
pulses SCLK eight times, while driving an 8-bit control
byte serially on SDIO. The device captures the data on
rising edges of SCLK. The control byte must have one
of five values:
page 7; Figure 2, “2-Wire Control Interface Read and
Write Timing Parameters,” on page 8, and Figure 3, “2-
Wire Control Interface Read and Write Timing Diagram,”
on page 8.
5.15.2. 3-Wire Control Interface Mode
When selecting 3-wire mode, the user must ensure that
a rising edge of SCLK does not occur within 300 ns
before the rising edge of RST.
The 3-wire bus mode uses the SCLK, SDIO, and SEN_
?
?
?
?
?
0x48 = write a command (controller drives 8
additional bytes on SDIO).
0x80 = read a response (device drives 1additional
byte on SDIO).
0xC0 = read a response (device drives 16 additional
bytes on SDIO).
0xA0 = read a response (device drives 1 additional
byte on GPO1).
0xE0 = read a response (device drives 16 additional
pins. A transaction begins when the user drives SEN
low. Next, the user drives a 9-bit control word on SDIO,
which is captured by the device on rising edges of
SCLK. The control word consists of a 9-bit device
address (A7:A5 = 101b), a read/write bit (read = 1, write
= 0), and a 5-bit register address (A4:A0).
For write operations, the control word is followed by a
16-bit data word, which is captured by the device on
rising edges of SCLK.
For read operations, the control word is followed by a
delay of one-half SCLK cycle for bus turn-around. Next,
the Si4736/37/38/39 will drive the 16-bit read data word
serially on SDIO, changing the state of SDIO on each
rising edge of SCLK.
A transaction ends when the user sets SEN high, then
pulses SCLK high and low one final time. SCLK may
either stop or continue to toggle while SEN is high.
In 3-wire mode, commands are sent by first writing each
argument to register(s) 0xA1–0xA3, then writing the
command word to register 0xA0. A response is
retrieved by reading registers 0xA8–0xAF.
For details on timing specifications and diagrams, refer
to Table 6, “3-Wire Control Interface Characteristics,” on
page 9; Figure 4, “3-Wire Control Interface Write Timing
Parameters,” on page 9, and Figure 5, “3-Wire Control
Interface Read Timing Parameters,” on page 9.
bytes on GPO1).
For write operations, the system controller must drive
exactly 8 data bytes (a command and seven arguments)
on SDIO after the control byte. The data is captured by
the device on the rising edge of SCLK.
For read operations, the controller must read exactly 1
byte (STATUS) after the control byte or exactly 16 data
bytes (STATUS and RESP1–RESP15) after the control
byte. The device changes the state of SDIO (or GPO1, if
specified) on the falling edge of SCLK. Data must be
captured by the system controller on the rising edge of
SCLK.
Keep SEN low until all bytes have transferred. A
transaction may be aborted at any time by setting SEN
high and toggling SCLK high and then low. Commands
will be ignored by the device if the transaction is
aborted.
For details on timing specifications and diagrams, refer
to Figure 6 and Figure 7 on page 10.
5.16. GPO Outputs
The Si4736/37/38/39 provides three general-purpose
output pins. The GPO pins can be configured to output
a constant low, constant high, or high-impedance. The
GPO pins can be reconfigured as specialized functions.
GPO2/INT can be configured to provide interrupts and
GPO3 can be configured to provide external crystal
support or as DCLK in digital audio output mode.
Rev. 1.0
25
相关PDF资料 |
PDF描述 |
|---|---|
| ZVP2106GTA | MOSFET P-CH 60V 450MA SOT223 |
| SI4730-D50-GM | IC RADIO RECEIVER AM/FM 20-QFN |
| ME701203 | DIODE MOD 3PH BRDG 1200V 30A |
| SI4738-C40-GU | IC RX FM/WB RADIO 24SSOP |
| SI4738-C40-GM | IC RX FM/WB RADIO 20UQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI4736-C40-GMR | 功能描述:射频接收器 Si4736 Broadcast AM/FM/WB Radio Recvr RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel |
| Si4736-C40-GU | 功能描述:射频接收器 BC AM/FM/WB Radio Receiver SSOP 24-pin RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel |
| SI4736-C40-GUR | 功能描述:射频接收器 Si4736 Broadcast AM/FM/WB Radio Rcvr RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel |
| SI4736DY | 制造商:Vishay Intertechnologies 功能描述:MOSFET, No. of Pins:8, Leaded Process Compatible:No, Mounting Type:Surface Mount |
| SI4736DY-T1-E3 | 功能描述:MOSFET 30V 13A 1.4W RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。