- 您现在的位置：买卖IC网 > PDF目录21347 > SI8400AB-B-IS (Silicon Laboratories Inc)IC ISOLATOR BIDIR I2C 8-SOIC PDF资料下载
参数资料
| 型号： | SI8400AB-B-IS |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 19/34页 |
| 文件大小： | 0K |
| 描述： | IC ISOLATOR BIDIR I2C 8-SOIC |
| 视频文件： | Digital Isolation Overview Digital Isolators vs. Optocouplers |
| 标准包装： | 96 |
| 输入 - 1 侧/2 侧： | 2/2 |
| 通道数： | 2 |
| 电源电压： | 3 V ~ 5.5 V |
| 电压 - 隔离： | 2500Vrms |
| 数据速率： | 10Mbps |
| 输出类型： | 开路漏极 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 125°C |
| 配用： | 336-1765-ND - KIT EVAL FOR SI84XXISO |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
Si840x
4.3. I 2 C Isolator Design Constraints
Table 13 lists the design constraints.
Table 13. Design Constraints
Design Constraint
To prevent the latch condition, the
isolator output low level must be
greater than the isolator input low
level.
Data Sheet Values
Isolator V OL 0.8 V typical
Isolator V IL 0.6 V typical
Input/Output Logic Low Level
Difference
Effect of Bus Pull-up Strength
and Temperature
This is normally guaranteed by the
isolator data sheet. However, if the
pull up strength is too weak, the out-
put low voltage will fall and can get
too close to the input low logic level.
? VSDA1, ? VSCL1 = 50 mV minimum These track over temperature.
If the pull up strength is too large,
The bus output low must be less
than the isolator input low logic
level.
The isolator output low must be
less than the bus input low.
Bus V OL = 0.4 V maximum
Isolator V IL = 0.45 V minimum
Bus V IL 0.3 x V DD = 1.0 V minimum for
V DD = 3.3 V
Isolator V OL = 0.825 V maximum,
(0.5 mA pullup, –10 to 125 °C)
the devices on the bus might not pull
the voltage below the input low
range. These have opposite tem-
perature coefficients. Worst case is
hot temperature.
If the pull up strength is too large,
the isolator might not pull below the
bus input low voltage.
Si8400/01/05 Vol: –1.8 mV/C
CMOS buffer: –0.6 mV/C
This provides some temperature
tracking, but worst case is cold tem-
perature.
4.4. I 2 C Isolator Design Considerations
The first step in applying an I 2 C isolator is to choose which side of the bus will be connected to the isolator A side.
Ideally, it should be the side which:
1. Is compatible with the range of bus pull up specified by the manufacturer. For example, the Si8400/01/02/05
isolators are normally used with a pull up of 0.5 mA to 3 mA.
2. Has the highest input low level for devices on the bus. Some devices may specify an input low of 0.9 V and
other devices might require an input low of 0.3 x Vdd. Assuming a 3.3 V minimum power supply, the side with
an input low of 0.3 x Vdd is the better side because this side has an input low level of 1.0 V.
3. Have devices on the bus that can pull down below the isolator input low level. For example, the Si840x input
level is 0.45 V. As most CMOS devices can pull to within 0.4 V of GND this is generally not an issue.
4. Has the lowest noise. Due to the special logic levels, noise margins can be as low as 50 mV.
The Si840x isolators are not compatible with devices that have a logic low of 0.8 V. For this situation, a discrete
circuit can be used. See “AN352: Low-Cost, High-Speed I 2 C Isolation with Digital Isolators” for additional
information.
Rev. 1.6
19
相关PDF资料 |
PDF描述 |
|---|---|
| M-ODC24A | OUTPUT MODULE DC 13MA 24VDC |
| SI8463BB-B-IS1 | IC ISOLATOR 6CH 5.5V 16-SOIC |
| KAL25JB10R0 | RES 10 OHM 25W 5% WW ALM |
| SI8462BB-B-IS1 | IC ISOLATOR 6CH 5.5V 16-SOIC |
| SI8461BB-B-IS1 | IC ISOLATOR 6CH 5.5V 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI8400AB-B-ISR | 功能描述:隔离器接口集成电路 2.5 kV Bidirectional I2C Isolator 1.7MHz RoHS:否 制造商:Texas Instruments 通道数量:2 传播延迟时间: 电源电压-最大:5.5 V 电源电压-最小:3 V 电源电流:3.6 mA 功率耗散: 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:SOIC-8 封装:Tube |
| SI-8400L | 制造商:SANKEN 制造商全称:Sanken electric 功能描述:Separate Excitation Switching Type with Coil |
| SI-8401 | 制造商:SANKEN 制造商全称:Sanken electric 功能描述:Separate Excitation Switching Type with Coil |
| Si8401AA-B-IS | 功能描述:隔离器接口集成电路 1.0 kV Bidirectional I2C Isolator 1.7MHz RoHS:否 制造商:Texas Instruments 通道数量:2 传播延迟时间: 电源电压-最大:5.5 V 电源电压-最小:3 V 电源电流:3.6 mA 功率耗散: 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:SOIC-8 封装:Tube |
| SI8401AA-B-ISR | 功能描述:隔离器接口集成电路 1kV Bidirect I2C Iso 1.7MHz ADuM RoHS:否 制造商:Texas Instruments 通道数量:2 传播延迟时间: 电源电压-最大:5.5 V 电源电压-最小:3 V 电源电流:3.6 mA 功率耗散: 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。