- 您现在的位置：买卖IC网 > PDF目录18848 > SI8501-C-IM (Silicon Laboratories Inc)SENSOR CURRENT 5A 5.5V UNI 12QFN PDF资料下载
参数资料
| 型号： | SI8501-C-IM |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 15/36页 |
| 文件大小： | 0K |
| 描述： | SENSOR CURRENT 5A 5.5V UNI 12QFN |
| 标准包装： | 490 |
| 电流 - 感应： | 5A |
| 精确度： | ±5% |
| 灵敏度： | 392mV/A |
| 电流 - 电源： | 4mA |
| 传感器类型： | 闭环 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 输出： | 可配置 |
| 频率： | 50kHz ~ 1MHz |
| 电极标记： | 单向 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 12-VFQFN |
| 包装： | 管件 |
| 产品目录页面： | 627 (CN2011-ZH PDF) |
| 其它名称： | 336-1718-5 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
Si85xx
3.3.2. Selecting Reset Timing Signals
Reset timing signals should be chosen to meet the
following conditions:
?
?
?
Satisfy reset time t R
Not overlap integrator reset into the desired
measurement period
Not violate reset watchdog timeout period t WD
3.3.3. Configuring Integrator Reset
Per Section “2. Functional Overview”, the integrator
must be reset (zeroed) prior to the start of each
measurement cycle to achieve specified measurement
accuracy. This reset must be synchronized with the
system switch timing signals to ensure that current is
measured during the appropriate time; so, the Si85xx
integrator reset circuitry uses system timing as its
reference. Timing signals connect to reset inputs R1
through R4 where built-in logic functions allow the user
to choose the conditions that cause an integrator reset
event. Important Note: reset inputs R1–R4 are rated to
a maximum input voltage of VDD. External resistor
dividers must be used when connecting driver output
signals to R1–R4 that swing beyond VDD.
As shown in Table 11, the Si850x integrator reset logic
is a simple XOR gate where reset is maintained (or
triggered, depending on use of the TRST input) when
states of reset inputs R1 and R2 are not equal.
where any one of three reset logic functions can cause
integrator reset. The output mode (Si851x) is
determined by the states of the Mode and R4 inputs, as
Preliminary Rev. 0.4
15
相关PDF资料 |
PDF描述 |
|---|---|
| 7L-19.200MCS-T | OSC VCTCXO 19.200 MHZ 2.5V SMD |
| 3781-8-8 | CORD MINIGRABBER PATCH 8" GRAY |
| 3781-8-7 | CORD MINIGRABBER PATCH 8" VIOLET |
| 3781-8-6 | CORD MINIGRABBER PATCH 8" BLUE |
| 3781-8-5 | CORD MINIGRABBER PATCH 8" GREEN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI8501-C-IMR | 制造商:Silicon Laboratories Inc 功能描述:5A CURRENT SENSOR, SINGLE OUTPUT 1KV QFN12 - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:SENSOR CURRENT 5A 5.5V UNI 12QFN 制造商:Silicon Laboratories Inc 功能描述:5A Current Sensor Single Output 1kV |
| Si8501-C-IS | 功能描述:板上安装电流传感器 5A SINGLE OUTPUT 5kV RoHS:否 制造商:Honeywell 电流额定值:+/- 56 A 传感器/变换器类型: 电源电压:4.75 VDC to 5.25 VDC 响应时间:< 0.2 us 输出电压: 工作温度:- 40 C to + 85 C 准确性:+/- 0.24 % 频率范围: |
| SI8501-C-ISR | 制造商:Silicon Laboratories Inc 功能描述:5A CURRENT SENSOR, SINGLE OUTPUT 5KV SOIC20 - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:SENSOR CURR 5A 5.5V UNI 20SOIC 制造商:Silicon Laboratories Inc 功能描述:5A Current Sensor Single Output 5kV |
| SI-8501L | 制造商:Sanken Electric Co Ltd 功能描述:Switching Mode Regulator 5-Pin 制造商:Sanken Electric Co Ltd 功能描述:IC REG BUCK ADJ 1A EI-19 制造商:ALLEGRO 功能描述:IC, LINEAR VOLTAGE REGULATOR 5V TO-220-6, Primary Input Voltage:20V, Output Volt 制造商:Allegro MicroSystems LLC 功能描述:IC, LINEAR VOLTAGE REGULATOR 5V TO-220-6, Primary Input Voltage:20V, Output Voltage Min:4.8V, Output Voltage Max:5.2V, Output Voltage Fixed:5V, No. of Pins:6, No. of Outputs:1, Output Current:1A, Operating Temperature Min:-20C , RoHS Compliant: Yes |
| Si8502-B-GM | 功能描述:板上安装电流传感器 10A Current Sensr Single Out RoHS:否 制造商:Honeywell 电流额定值:+/- 56 A 传感器/变换器类型: 电源电压:4.75 VDC to 5.25 VDC 响应时间:< 0.2 us 输出电压: 工作温度:- 40 C to + 85 C 准确性:+/- 0.24 % 频率范围: |
发布紧急采购，3分钟左右您将得到回复。