- 您现在的位置：买卖IC网 > PDF目录13093 > SI9130CG-E3 (Vishay Siliconix)IC CTRLR PWM PIN PROG 28SSOP PDF资料下载
参数资料
| 型号： | SI9130CG-E3 |
| 厂商： | Vishay Siliconix |
| 文件页数： | 12/15页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM PIN PROG 28SSOP |
| 标准包装： | 225 |
| 应用： | 控制器，移动式个人电脑 |
| 输入电压： | 5.5 V ~ 30 V |
| 输出数： | 2 |
| 输出电压： | 5V，可编程 |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 散装 |
Si9130
Vishay Siliconix
OPERATIONAL MODES
PWM Mode
Product is End of Life 3/2014
The SYNC pin can be driven with an external CMOS level
signal with frequency from 240 kHz and 350 kHz to
The 3.3 V and 5 V Buck controllers operate in continuous-
current PWM mode when the load demands more than
approximately 25 % of the maximum current (see typical
curves). The duty cycle can be approximated as Duty_Cycle
= V OUT /V IN .
In this mode, the inductor current is continuous; in the first
half of the cycle, the current slopes up when the high-side
MOSFET conducts and then, in the second half, slopes back
down when the inductor is providing energy to the output
capacitor and load. As current enters the inductor in the first
half-cycle, it is also continuing through to the load; hence, the
load is receiving continuous current from the inductor. By
using this method, output ripple is minimized and smaller
form-factor inductors can be used. The output capacitor’s
ESR has the largest effect on output ripple. It is typically
under 50 mV; the worst case condition is under light load with
higher input battery voltage.
Pulse-Skipping Mode
When the load requires less than 25 % of its maximum, the
Si9130 enters a mode which drives the gate for one clock
cycle and skips the majority of the remaining cycles. Pulse-
skipping mode cuts down on the switching losses, the
dominant power consumer at low current levels.
In the region between pulse-skipping mode and PWM mode,
the controller may transition between the two modes,
delivering spurts of pulses. This may cause the current
waveform to look irregular, but will not overly affect the ripple
voltage. Even in this transitioning mode efficiency will stay
high.
Current Limit
The current through an external resistor, is constantly
monitored to protect against over-current. A low value
resistor is placed in series with the inductor. The voltage
across it is measured by connecting it between CS_ and
FB_. If this voltage is larger than 100 mV, the high-side
MOSFET drive is shut down. Eliminating over-currents
protects the MOSFET, the load and the power source.
Typical values for the sense resistors with a 3 A load will be
25 m Ω .
Oscillator and SYNC
There are two ways to set the Si9130 oscillator frequency: by
using an external SYNC signal, or using the internal
oscillator.
www.vishay.com
12
synchronize to the internal oscillator. Tying SYNC to either
V L or GND sets the frequency to 200 kHz and to REF sets
the frequency to 300 kHz.
Operation at 300 kHz is typically used to minimize output
passive component sizes. Slower switching speeds of
200 kHz may be needed for lower input voltages.
Internal V L and REF
A 5 V linear regulator supplies power to the internal logic
circuitry. The regulator is available for external use from pin
V L , able to source 5 mA. A 4.7 μF capacitor should be
connected between V L and GND. To increase efficiency,
when the 5 V switching supply has voltage greater than
4.5 V, V L is internally switched over to the output of the 5 V
switching supply and the linear regulator is turned off.
The 5 V linear regulator provides power to the internal 3.3 V
bandgap reference (REF). The 3.3 V reference can supply
5 mA to an external load, connected to pin REF. Between
REF and GND connect a capacitor, 0.22 μF plus 1 μF per mA
of load current. The switching outputs will vary with the
reference; therefore, placing a load on the REF pin will cause
the main outputs to decrease slightly, within the specified
regulation tolerance.
V L and REF supplies stay on as long as V+ is greater than
4.5 V, even if the switching supplies are not enabled. This
feature is necessary when using the micropower regulators
to keep memory alive during shutdown.
Both linear regulators can be connected to their respective
switching supply outputs. For example, REF would be tied to
the output of the 3.3 V and V L to 5 V. This will keep the main
supplies up in standby mode, provided that each load current
in shutdown is not larger than 5 mA.
Fault Protection
The 3.3 V and 5 V switching controllers are shut down when
one of the linear regulators drops below 85 % of its nominal
value; that is, shut down will occur when
V L < 4.0 V or REF < 2.8 V.
Document Number: 70190
S11-0975-Rev. G, 16-May-11
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J5M-CZ-B1 | CONVERTER MOD DC/DC 10V 25W |
| VI-B54-EU-F1 | CONVERTER MOD DC/DC 48V 200W |
| VI-J1F-EZ-B1 | CONVERTER MOD DC/DC 72V 25W |
| C0603X7R1A103M | CAP CER 10000PF 10V 20% X7R 0201 |
| VE-J51-CZ-B1 | CONVERTER MOD DC/DC 12V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI9130CG-T1 | 功能描述:电流型 PWM 控制器 Pin-Programmable Dual Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| SI9130CG-T1-E3 | 功能描述:IC CTRLR PWM PIN PROG 28SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器，DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP（0.173"，4.40mm 宽） 供应商设备封装:30-TSSOP 包装:带卷 (TR) |
| SI9130DB | 功能描述:电流型 PWM 控制器 SI9130 Demo Board RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| SI9130LG | 功能描述:电流型 PWM 控制器 Prog Dual Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| SI9130LG-E3 | 功能描述:电流型 PWM 控制器 Pin-Programmable Dual Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。