- 您现在的位置：买卖IC网 > PDF目录1243 > SKP16C26A (Renesas Electronics America)DEV EVALUATION KIT M16C/26A PDF资料下载
参数资料
| 型号： | SKP16C26A |
| 厂商： | Renesas Electronics America |
| 文件页数： | 17/22页 |
| 文件大小： | 0K |
| 描述： | DEV EVALUATION KIT M16C/26A |
| 其它有关文件： | SKP16C26A Schematic |
| 标准包装： | 1 |
Applications Engineering
A.2.3 KD30 Already Exists
When a message ‘KD30 already exists’ is displayed, the usual cause of this problem is that the
KD30 application was not properly closed. Please unplug the USB cable first and wait a few
seconds. Then check if KD30 is already running by looking at your task bar. If KD30 cannot be
found there, bring up Task Manager (press CTRL-ALT-DEL once and click on ‘Task Manager’
button). Select KD30.exe on the ‘Processes’ list and click on ‘End Process’ to terminate KD30.
Then re-plug in the USB cable and restart KD30.
A.2.4 Issues that may come up During Debug Operations
While using KD30 to debug user code, some issues may come up because the limitations
discussed in section 6 were not satisfied. The common issues are listed on table A.2, including
the countermeasures.
Table A.2. Problems while using KD30
Problem Possible Cause/s and Solution
After stepping a few ? Changes were made to UART1 SFR’s. Do NOT change
instructions, KD30 hangs UART1 SFRs in user program.
Breakpoints do not seem to ? KD30 is in “FreeRun” mode. Change the RUN mode to
work “Sampling” from the “Init” window (Environment > Init).
KD30 locks up (cannot stop ? Changes were made to UART1 SFR’s. Do NOT change
program) or UART1 SFRs in user program.
Communication error ? Ensure no limitations in Section 6 were violated.
message is displayed. ? Re-initialize the system without closing KD30. See note
below.
? Do a hardware reset. User-program runaway may be
corrupting the kernel (RAM, interrupt vectors, flags, etc.)
Close KD30, hit reset button on the SKP16C26A to reset the
board, and then restart KD30.
Download problems ? Filenames or directory names contain spaces or special
characters.
? HEW project not properly set up (startup files missing or out
of order, files added to wrong member, etc). Try creating a
new project and adding your source files to it. For details,
please see HEW user’s manual.
To re-initialize the system without closing KD30, try the following:
?
?
?
?
Press the [OK] button on the error dialog box to close it.
When an Exit dialog box appears, press the [Cancel] button to close it.
Hit reset button on the SKP16C26A board.
Press KD30 reset button.
After initialization, debugging can resume. However, it is recommended that you download your
program again before debugging.
Note: If it has been identified that there are problems with the ICD, please see the ICD’s (RTA-
FoUSB-MON) user’s manual and troubleshooting section of this manual.
SKP16C26A User’s Manual Rev. 1.0
16 / 21
June 2004
相关PDF资料 |
PDF描述 |
|---|---|
| SKP32C85-100-CL | DEV EVALUATION KIT M32C/85 100PN |
| SKP8CMINI-13 | BOARD DEV EVALUATION FOR R8C/13 |
| SKP8CMINI-17 | KIT EVAL STARTER FOR R8C/17 |
| SKP8CMINI | DEV EVALUATION KIT R8C/11 |
| SL03 10001 | CURRENT LIMITER INRUSH 10 OHM 1A |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SKP16CMINI28 | 功能描述:DEV EVALUATION KIT SKP16CMINI28 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| SKP202 | 制造商:SANKEN 制造商全称:Sanken electric 功能描述:N-Channel MOS FET |
| SKP202VR | 制造商:Sanken Electric Co Ltd 功能描述:MOSFET N-CH 200V 45A TO-263 |
| SKP221M1AE11VMP | 制造商:JAMICON 功能描述: |
| SKP2-30 | 制造商:Tamura Corporation of America 功能描述:Ind Power Toroid 45uH 1KHz RDL |
发布紧急采购，3分钟左右您将得到回复。