iPAC PA MODULE FOR QUAD-BAND GSM / GPRS
DATA SHEET SKY77324
Skyworks Solutions, Inc. Phone [781] 376-3000 Fax [781] 376-3100 sales@skyworksinc.com www.skyworksinc.com
103123D Skyworks Proprietary and Confidential information. Products and product information are subject to change without notice. June 9, 2005
11
Table 3. SKY77324 Electrical Specifications (1) (9 of 9)
PCS1900 Mode (f = 1850 to 1910 MHz and PIN = 0 to 6 dBm) [continued]
Parameter
Symbol
Test Condition
Minimum
Typical
Maximum
Units
Time from POUT = –10 dBm to within
0.5 dBm of POUT = +1.5 dBm
—
0.5
3.0
Time from POUT = –10 dBm to within
0.5 dBm of POUT = +20.0 dBm
—
0.8
1.1
Open Loop (4) Switching time
τ
RISE
,
τ
FALL
Time from POUT = –10 dBm to within
0.5 dBm of POUT = +32.0 dBm
—
1.2
1.5
s
Spurious
Spur
All combinations of the following parameters:
VAPC = controlled (3)
PIN = min. to max.
VCC = 2.9 V to 4.8 V
Load VSWR = 8:1, all phase angles
No parasitic oscillation > –36 dBm
Load mismatch
Load
All combinations of the following parameters:
VAPC = controlled (3)
PIN = min. to max.
VCC = 2.9 V to 4.8 V
Load VSWR = 10:1, all phase angles
No module damage or permanent degradation
At fO + 20 MHz
RBW = 100 kHz
VCC = 3.5 V
1.5 dBm
≤ POUT ≤ 32.0 dBm
TCASE = +25 °C
—
–82
–80
Noise power
PNOISE
At 869 to 894 MHz
RBW = 100 kHz
VCC = 3.5 V
1.5 dBm
≤ POUT ≤ 32.0 dBm
TCASE = +25 °C
—
–97
–87
dBm
Power control dynamic range
PCDR
—
35
50
—
dB
POUT +15.5 to +32.0 dBm, +25 °C
–1.0
—
+1.0
Power control variation (5)
(Control level 0–8) 3.2 V
≤ VCC ≤ 4.5 V
PCV
POUT +15.5 to +32.0 dBm
–1.6
—
+1.6
dB
POUT +5.5 to +13.5 dBm, +25 °C
–1.8
—
+1.8
Power control variation (5)
(Control level 9–13)
PCV
POUT +5.5 to +13.5 dBm
–3.3
—
+3.3
dB
POUT +1.5 to +3.5 dBm, +25 °C
–3.0
—
+3.0
Power control variation (5)
(Control level 14–15)
PCV
POUT +1.5 to +3.5 dBm
–4.5
—
+4.5
dB
Power control slope
PCS
1.5 to 32.0 dBm
—
400
dB/V
Closed loop bandwidth
BCL
VAPC = 1.0 V
—
500
—
kHz
Loop phase margin
PM
VAPC = 1.0 V
75
—
deg.
(1) Unless specified otherwise:
TCASE = –25 °C to maximum operating temperature (see Table 2)
RL = 50
pulsed operation with pulse width
≤ 1154 s and duty cycle ≤ 2:8
Vcc = 2.9 V to 4.8 V.
(2) Icc = 0A to xA, where x = current at POUT = 34.5 dBm, 50
load, and Vcc = 3.5 V.
(3) Icc = 0A to xA, where x = current at POUT = 32.0 dBm, 50
load, and Vcc = 3.5 V.
(4) This device has an Open Loop mode that allows bypassing of the internal PAC circuitry. See the Technical Information section at end of this document for further information.
(5) Power control variation is measured by comparing power obtained at a specified control voltage over all conditions, against the power obtained with the same control voltage at nominal
conditions. For this module, nominal conditions are defined as
T = 25 °C
VCC = 3.5 V
PIN = 3 dBm
Frequency = mid-band