- 您现在的位置：买卖IC网 > PDF目录8718 > SL23EP09ZI-1T (Silicon Laboratories Inc)IC BUFFER 220MHZ 9CH3.3V 16TSSOP PDF资料下载
参数资料
| 型号： | SL23EP09ZI-1T |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 2/14页 |
| 文件大小： | 0K |
| 描述： | IC BUFFER 220MHZ 9CH3.3V 16TSSOP |
| 标准包装： | 2,500 |
| 系列： | EProClock® |
| 类型： | * |
| PLL： | 带旁路 |
| 输入： | 时钟 |
| 输出： | 时钟 |
| 电路数： | 1 |
| 比率 - 输入:输出： | 1:9 |
| 差分 - 输入:输出： | 无/无 |
| 频率 - 最大： | 220MHz |
| 除法器/乘法器： | 无/无 |
| 电源电压： | 2.3 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | * |
| 封装/外壳： | * |
| 供应商设备封装： | * |
| 包装： | * |
Rev 2.0, May 12, 2008
Page 10 of 14
SL23EP09
External Components & Design Considerations
Typical Application Schematic
SL23EP09
CL
0.1
μF
0.1
μF
CLKIN
CLKOUT
CLKA1
CLKB4
GND
S1
S2
VDD
1
4
13
9
8
5
12
11
2
16
VDD
Comments and Recommendations
Decoupling Capacitor:
A decoupling capacitor of 0.1μF must be used between VDD and VSS pins. Place the capacitor on
the component side of the PCB as close to the VDD pin as possible. The PCB trace to the VDD pin and to the GND via
should be kept as short as possible. Do not use vias between the decoupling capacitor and the VDD pin.
Series Termination Resistor: A series termination resistor is recommended if the distance between the output clocks and
the load is over 1 inch. The nominal impedance of the clock outputs is given on the page 4. Place the series termination
resistors as close to the clock outputs as possible.
Zero Delay and Skew Control: All outputs and CLKIN pins should be loaded with the same load to achieve “Zero Delay”
between the CLKIN and the outputs. The CLKOUT pin is connected to CLKIN internally on-chip for feedback to PLL, and
sees an additional 2 pF load with respect to Bank A and B clocks. For applications requiring zero input/output delay, the load
at the all output pins including the CLKOUT pin must be the same. If any delay adjustment is required, the capacitance at
the CLKOUT pin could be increased or decreased to increase or decrease the delay between Bank A and B clocks and
CLKIN.
For minimum pin-to-pin skew, the external load at all the Bank A and B clocks must be the same.
相关PDF资料 |
PDF描述 |
|---|---|
| AD5321BRTZ-REEL | IC DAC 12BIT 2WIRE I2C SOT23-6 |
| VI-211-MW-F2 | CONVERTER MOD DC/DC 12V 100W |
| VE-234-MW-F1 | CONVERTER MOD DC/DC 48V 100W |
| V24A5H400BF | CONVERTER MOD DC/DC 5V 400W |
| SL2309ZI-1HT | IC BUFFER 140MHZ 9CH3.3V 16TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SL23HE3/2CT | 功能描述:肖特基二极管与整流器 30 Volt 2.0 Amp 100 Amp IFSM RoHS:否 制造商:Skyworks Solutions, Inc. 产品:Schottky Diodes 峰值反向电压:2 V 正向连续电流:50 mA 最大浪涌电流: 配置:Crossover Quad 恢复时间: 正向电压下降:370 mV 最大反向漏泄电流: 最大功率耗散:75 mW 工作温度范围:- 65 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-143 封装:Reel |
| SL23HE3/52T | 功能描述:肖特基二极管与整流器 30 Volt 2.0 Amp 100 Amp IFSM RoHS:否 制造商:Skyworks Solutions, Inc. 产品:Schottky Diodes 峰值反向电压:2 V 正向连续电流:50 mA 最大浪涌电流: 配置:Crossover Quad 恢复时间: 正向电压下降:370 mV 最大反向漏泄电流: 最大功率耗散:75 mW 工作温度范围:- 65 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-143 封装:Reel |
| SL23HE3/55T | 功能描述:肖特基二极管与整流器 30 Volt 2.0 Amp 100 Amp IFSM RoHS:否 制造商:Skyworks Solutions, Inc. 产品:Schottky Diodes 峰值反向电压:2 V 正向连续电流:50 mA 最大浪涌电流: 配置:Crossover Quad 恢复时间: 正向电压下降:370 mV 最大反向漏泄电流: 最大功率耗散:75 mW 工作温度范围:- 65 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-143 封装:Reel |
| SL23HE3/5BT | 功能描述:肖特基二极管与整流器 30 Volt 2.0 Amp 100 Amp IFSM RoHS:否 制造商:Skyworks Solutions, Inc. 产品:Schottky Diodes 峰值反向电压:2 V 正向连续电流:50 mA 最大浪涌电流: 配置:Crossover Quad 恢复时间: 正向电压下降:370 mV 最大反向漏泄电流: 最大功率耗散:75 mW 工作温度范围:- 65 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-143 封装:Reel |
| SL23-L | 制造商:FORMOSA 制造商全称:Formosa MS 功能描述:Low VF Chip Schottky Barrier Diodes - Silicon epitaxial planer type |
发布紧急采购，3分钟左右您将得到回复。