- 您现在的位置：买卖IC网 > PDF目录373461 > SN54LVTH182646AHV (Texas Instruments, Inc.) Octal 3-State Noninverting Buffer/Line Driver/Line Receiver; Package: TSSOP 20 LEAD; No of Pins: 20; Container: Rail; Qty per Container: 75 PDF资料下载
参数资料
| 型号： | SN54LVTH182646AHV |
| 厂商： | Texas Instruments, Inc. |
| 英文描述： | Octal 3-State Noninverting Buffer/Line Driver/Line Receiver; Package: TSSOP 20 LEAD; No of Pins: 20; Container: Rail; Qty per Container: 75 |
| 中文描述： | 的3.3V ABT生根粉扫描测试设备与18位收发器和寄存器 |
| 文件页数： | 8/36页 |
| 文件大小： | 551K |
| 代理商： | SN54LVTH182646AHV |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
SN54LVTH18646A, SN54LVTH182646A, SN74LVTH18646A, SN74LVTH182646A
3.3-V ABT SCAN TEST DEVICES
WITH 18-BIT TRANSCEIVERS AND REGISTERS
SCBS311D – MARCH 1994 – REVISED JUNE 1997
8
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
state diagram description
The TAP controller is a synchronous finite state machine that provides test control signals throughout the device.
The state diagram shown in Figure 2 is in accordance with IEEE Std 1149.1-1990. The TAP controller proceeds
through its states based on the level of TMS at the rising edge of TCK.
As shown, the TAP controller consists of 16 states. There are six stable states (indicated by a looping arrow in
the state diagram) and ten unstable states. A stable state is defined as a state the TAP controller can retain for
consecutive TCK cycles. Any state that does not meet this criterion is an unstable state.
There are two main paths through the state diagram: one to access and control the selected data register and
one to access and control the instruction register. Only one register can be accessed at a time.
Test-Logic-Reset
The device powers up in the Test-Logic-Reset state. In the stable Test-Logic-Reset state, the test logic is reset
and is disabled so that the normal logic function of the device is performed. The instruction register is reset to
an opcode that selects the optional IDCODE instruction, if supported, or the BYPASS instruction. Certain data
registers can also be reset to their power-up values.
The state machine is constructed such that the TAP controller returns to the Test-Logic-Reset state in no more
than five TCK cycles if TMS is left high. The TMS pin has an internal pullup resistor that forces it high if left
unconnected or if a board defect causes it to be open circuited.
For the ’LVTH18646A and ’LVTH182646A, the instruction register is reset to the binary value 10000001, which
selects the IDCODE instruction. Bits 51–48 in the boundary-scan register are reset to logic 0, ensuring that
these cells, which control A-port and B-port outputs, are set to benign values (i.e., if test mode were invoked,
the outputs would be at high-impedance state). Reset values of other bits in the boundary-scan register should
be considered indeterminate. The boundary-control register is reset to the binary value 010, which selects the
PSA test operation.
Run-Test/Idle
The TAP controller must pass through the Run-Test/Idle state (from Test-Logic-Reset) before executing any test
operations. The Run-Test/Idle state also can be entered following data-register or instruction-register scans.
Run-Test/Idle is a stable state in which the test logic can be actively running a test or can be idle. The test
operations selected by the boundary-control register are performed while the TAP controller is in the
Run-Test/Idle state.
Select-DR-Scan, Select-lR-Scan
No specific function is performed in the Select-DR-Scan and Select-lR-Scan states, and the TAP controller exits
either of these states on the next TCK cycle. These states allow the selection of either data-register scan or
instruction-register scan.
Capture-DR
When a data-register scan is selected, the TAP controller must pass through the Capture-DR state. In the
Capture-DR state, the selected data register can capture a data value as specified by the current instruction.
Such capture operations occur on the rising edge of TCK, upon which the TAP controller exits the
Capture-DR state.
相关PDF资料 |
PDF描述 |
|---|---|
| SN54LVTH18646AHV | Octal 3-State Noninverting Buffer/Line Driver/Line Receiver; Package: SOEIAJ-20; No of Pins: 20; Container: Tape and Reel; Qty per Container: 2000 |
| SN54LVTH182652AHV | Octal 3-State Noninverting Buffer/Line Driver/Line Receiver; Package: TSSOP 20 LEAD; No of Pins: 20; Container: Tape and Reel; Qty per Container: 2500 |
| SN54LVTH18652AHV | Octal 3-State Noninverting Buffer/Line Driver/Line Receiver; Package: 20 LEAD PDIP; No of Pins: 20; Container: Rail; Qty per Container: 18 |
| SN54LVTH18512 | 3.3-V ABT Scan Test Device With 18-Bit Universal Bus Transceivers(3.3VABT扫描测试装置(18位通用总线收发器)) |
| SN54LVTH182512 | 3.3-V ABT Scan Test Device With 18-Bit Universal Bus Transceivers(3.3VABT扫描测试装置(18位通用总线收发器)) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SN54S00J | 制造商:Texas Instruments 功能描述:NAND Gate 4-Element 2-IN Bipolar 14-Pin CDIP Tube 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| SN54S00W | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| SN54S02J | 制造商:Texas Instruments 功能描述: |
| SN54S03J | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Texas Instruments 功能描述:2-INPUT NAND GATE (OC) - Rail/Tube |
| SN54S04J | 制造商:Texas Instruments 功能描述:Inverter 6-Element Bipolar 14-Pin CDIP Tube 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Texas Instruments 功能描述:INVERTER 6-ELEM BIPOLAR 14CDIP - Rail/Tube 制造商:Texas Instruments 功能描述:HEX INVERTER *NIC* |
发布紧急采购，3分钟左右您将得到回复。