参数资料
型号: SN75107AJ
厂商: TEXAS INSTRUMENTS INC
元件分类: Buffer和线驱动
英文描述: DUAL LINE RECEIVER, CDIP14
文件页数: 2/19页
文件大小: 296K
代理商: SN75107AJ
SN55107A, SN75107A, SN75107B, SN75108A
DUAL LINE RECEIVERS
SLLS069D – JANUARY 1977 – REVISED APRIL 1998
10
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
basic balanced-line transmission system
The ’107A, SN75107B, and SN75108A dual line devices are designed specifically for use in high-speed
data-transmission systems that utilize balanced terminated transmission lines, such as twisted-pair lines. The
system operates in the balanced mode, so noise induced on one line is also induced on the other. The noise
appears common mode at the receiver input terminals, where it is rejected. The ground connection between
the line driver and receiver is not part of the signal circuit; therefore, system performance is not affected by
circulating ground currents.
The unique driver-output circuit allows terminated transmission lines to be driven at normal line impedances.
High-speed system operation is ensured because line reflections are virtually eliminated when terminated lines
are used. Crosstalk is minimized by low signal amplitudes and low line impedances.
The typical data delay in a system is approximately 30 + 1.3 L ns, where L is the distance in feet separating the
driver and receiver. This delay includes one gate delay in both the driver and receiver.
Data is impressed on the balanced-line system by unbalancing the line voltages with the driver output current.
The driven line is selected by appropriate driver-input logic levels. The voltage difference is approximately:
VDIFF ≈ 1/2IO(on) RT
High series line resistance causes degradation of the signal. However, the receivers detect signals as low as
25 mV. For normal line resistances, data can be recovered from lines of several thousand feet in length.
Line-termination resistors (RT) are required only at the extreme ends of the line. For short lines, termination
resistors at the receiver only may be adequate. The signal amplitude is then approximately:
VDIFF ≈ IO(on) RT
Transmission Line Having
Characteristic Impedance ZO
RT = ZO/2
L
RT
A
B
C
D
Strobes
RT
Y
Receiver
‘107A, SN75107B,
SN75108A
Driver
SN55110A, SN75110A,
SN75112
Data Input
Inhibit
Figure 11. Typical Differential Data Line
data-bus or party-line system
The strobe feature of the receivers and the inhibit feature of the drivers allow these dual line devices to be used
in data-bus or party-line systems. In these applications, several drivers and receivers can share a common
transmission line. An enabled driver transmits data to all enabled receivers on the line while other drivers and
receivers are disabled. Data is time multiplexed on the transmission line. The device specifications allow widely
varying thermal and electrical environments at the various driver and receiver locations. The data-bus system
offers maximum performance at minimum cost.
相关PDF资料
PDF描述
SN75107BJ DUAL LINE RECEIVER, CDIP14
SN75153J-00 LINE DRIVER, CDIP16
SN75HVD08 3.3/5-V RS-485 Transceiver
SN75HVD08D WIDE SUPPLY RANGE RS-485 TRANSCEIVER
SN75LBC976DL LINE TRANSCEIVER, PDSO56
相关代理商/技术参数
参数描述
SN75107AN 功能描述:总线接收器 Dual Line RoHS:否 制造商:Texas Instruments 接收机数量:4 接收机信号类型:Differential 接口类型:EIA/TIA-422-B, V.11 工作电源电压:3.3 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:TSSOP-16 封装:Reel
SN75107AN 制造商:Texas Instruments 功能描述:LINE RECEIVER DUAL 75107 DIP14
SN75107ANE4 功能描述:缓冲器和线路驱动器 DUAL LINE RECEIVER RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel
SN75107ANS 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述:
SN75107ANSR 功能描述:缓冲器和线路驱动器 DUAL LINE RECEIVER RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel