- 您现在的位置：买卖IC网 > PDF目录17413 > SP7662EB (Exar Corporation)EVAL BOARD FOR SP7662 PDF资料下载
参数资料
| 型号： | SP7662EB |
| 厂商： | Exar Corporation |
| 文件页数： | 5/19页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR SP7662 |
| 标准包装： | 1 |
| 系列： | * |
S P 7 6 6 2
P o w e r b l o x T M
1 2 A 3 0 0 K H z S y n c h r o n o u s S t e p D o w n R e g u l a t o r
PIN DESCRIPTION
Name
PGND
GND
VFB
COMP
SS
ISN
ISP
SWN
VINP
LX
BST
VIN
UVIN
VCC
Pin Number
1-4
5,9,19,20,28
6
7
8
10
11
12
13, 29
14-16, 23-27
17
18
21
22
Description
Ground connection for the synchronous rectifier.
Ground Pin. The control circuitry of the IC and lower power driver are referenced to this
pin. Return separately from other ground traces to the (-) terminal of C OUT .
Feedback Voltage and Short Circuit Detection pin. It is the inverting input of the Error
Amplifier and serves as the output voltage feedback point for the Buck Converter. The
output voltage is sensed and can be adjusted through an external resistor divider.
Whenever V FB drops 0.25V below the positive reference, a short circuit fault is detected
and the IC enters hiccup mode.
Output of the Error Amplifier. It is internally connected to the inverting input of the
PWM comparator. An optimal filter combination is chosen and connected to this pin and
either ground or V FB to stabilize the voltage mode loop.
Soft Start. Connect an external capacitor between SS and GND to set the soft start rate
based on the 10μA source current. The SS pin is held low via a 1mA (min) curren t
during all fault conditions.
Current sense negative input. Rail-to-rail input for over current detection.
Current sense positive input. Rail-to-rail input for over current detection.
Lower supply rail for the GH high-side gate driver. Connect this pin to the switching
node as close as possible to pins 23- 27. Do not connect this pin to pins 14 – 16.
Input connection to the high side N-channel MOSFET.
Connect an inductor between this pin and V OUT .
High side driver supply pin. Connect BST to the external boost diode and capacitor as
shown in the Typical Application Circuit on page 1. The high side driver is connected
between BST pin and SWN pin.
V IN connection for internal LDO and PWM Controller.
UVLO input for V IN voltage. Connect a resistor divider between V IN and UVIN to set
minimum operating voltage. Use resistor values below 20kΩ to override internal resistor
divider.
Output of internal regulator. May be externally biased if V IN < 5V.
ORDERING INFORMATION
Part Number
SP7662ER-L
SP7662ER-L/TR
Junction
Temperature
Range
- 40°C≤T J ≤+ 125°C
- 40°C≤T J ≤+ 125°C
Marking
SP7662ER
YYWWL
X
SP7662ER
YYWWL
X
Package
26-pin DFN
26-pin DFN
Packing
Quantity
Bulk
3K/Tape & Reel
Note 1
Lead Free
Lead Free
Note 2
SP7662EB
SP7662 Evaluation Board
“YY” = Year – “WW” = Work Week – “X” = Lot Number
? 2012 Exar Corporation
5/19
Rev. 2.1.0
相关PDF资料 |
PDF描述 |
|---|---|
| SP7655EB | EVAL BOARD FOR SP7655 |
| SP7653EB | EVAL BOARD FOR SP7653 |
| A9CAA-0804F | FLEX CABLE - AFG08A/AF08/AFG08T |
| LM2735YSDEVAL | BOARD EVAL LM2735 520KHZ 6LLP |
| A9AAT-1606F | FLEX CABLE - AFE16T/AF16/AFE16T |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SP7662ER | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:Evaluation Board Manual |
| SP7662ER/TR | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:Wide Input Voltage Range 12A, 300kHz, Buck Regulator |
| SP7662ER-L | 功能描述:开关变换器、稳压器与控制器 Buck Regulator RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| SP7662ERL/TR | 制造商:SIPEX 制造商全称:Sipex Corporation 功能描述:Wide Input Voltage Range 12A, 300kHz, Buck Regulator |
| SP7662ER-L/TR | 功能描述:开关变换器、稳压器与控制器 WIDE INPUT VOLTAGE Range12A300KHz RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。