收藏本站
参数资料
型号： SPC5200CBV400
厂商： Freescale Semiconductor
文件页数： 63/72页
文件大小： 0K
描述： IC MPU 32BIT 400MHZ 272-PBGA
标准包装： 40
系列： MPC52xx
处理器类型： 32-位 MPC52xx PowerPC
速度： 400MHz
电压： 1.5V
安装类型： 表面贴装
封装/外壳： 272-BBGA
供应商设备封装： 272-PBGA（27x27）
包装： 托盘
MPC5200B Data Sheet, Rev. 4
66
Freescale Semiconductor
3.3.2
Pull-up Requirements for the PCI Control Lines
If the PCI interface is NOT used (and internally disabled) the PCI control pins must be terminated as indicated by the PCI Local
Bus specification. This is also required for MOST/Graphics and Large Flash Mode.
PCI control signals always require pull-up resistors on the motherboard (not the expansion board) to ensure that they contain
stable values when no agent is actively driving the bus. This includes PCI_FRAME, PCI_TRDY, PCI_IRDY, PCI_DEVSEL,
PCI_STOP, PCI_SERR, PCI_PERR, and PCI_REQ.
3.3.3
Pull-up/Pull-down Requirements for MEM_MDQS Pins (SDRAM)
The MEM_MDQS[3:0] signals are not used with SDR memories and require pull-up or pull-down resistors in SDRAM mode.
3.3.4
.
Pull-up/Pull-down Requirements for MEM_MDQS Pins (DDR 16-bit
Mode)
The MEM_MDQS[1:0] signals are not used in DDR 16-bit mode and require pull-down resistors.
3.4
JTAG
The MPC5200B provides the user an IEEE 1149.1 JTAG interface to facilitate board/system testing. It also provides a Common
On-Chip Processor (COP) Interface, which shares the IEEE 1149.1 JTAG port. The COP Interface provides access to the
MPC5200B's embedded Freescale (formerly Motorola) MPC603e e300 processor. This interface provides a means for
executing test routines and for performing software development and debug functions.
3.4.1
JTAG_TRST
Boundary scan testing is enabled through the JTAG interface signals. The JTAG_TRST signal is optional in the IEEE 1149.1
specification but is provided on all processors that implement the PowerPC architecture. To obtain a reliable power-on reset
performance, the JTAG_TRST signal must be asserted during power-on reset.
3.4.1.1
JTAG_TRST and PORRESET
The JTAG interface can control the direction of the MPC5200B I/O pads via the boundary scan chain. The JTAG module must
be reset before the MPC5200B comes out of power-on reset; do this by asserting JTAG_TRST before PORRESET is released.
For more details refer to the Reset and JTAG Timing Specification.
Figure 53. PORRESET vs. JTAG_TRST
3.4.1.2
Connecting JTAG_TRST
The wiring of the JTAG_TRST depends on the existence of a board-related debug interface. (see below)
JTAG_TRST
PORRESET
Required assertion of JTAG_TRST
Optional assertion of JTAG_TRST
相关PDF资料
PDF描述
SPC5200CVR400 IC MPU 32BIT 400MHZ 272-PBGA
SPC5517GAMMG66 IC MCU 32B 1.5MB FLASH 208MAPBGA
SPC5604PGF0MLQ6 IC MCU 32BIT 512KB FLASH 144LQFP
SST89C58RC-40-C-QIF IC MCU 8BIT FLASH 40WQFN
SST89E54RC-33-C-PIE IC MCU 8BIT 17KB FLASH 40PDIP
相关代理商/技术参数
参数描述
SPC5200CBV400B 功能描述:微处理器 - MPU HABANERO AUTO RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
SPC5200CBV400B 制造商:Freescale Semiconductor 功能描述:IC 32BIT MPU 400MHZ BGA-272
SPC5200CBV400BR2 功能描述:微处理器 - MPU HABANERO - AUTO RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324
SPC5200CBV400R2 功能描述:IC MPU 32BIT 400MHZ 272-PBGA RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微处理器 系列:MPC52xx 标准包装:60 系列:SCC 处理器类型:Z380 特点:全静电 Z380 CPU 速度:20MHz 电压:5V 安装类型:表面贴装 封装/外壳:144-LQFP 供应商设备封装:144-LQFP 包装:托盘
SPC5200CVR400 功能描述:IC MPU 32BIT 400MHZ 272-PBGA RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微处理器 系列:MPC52xx 标准包装:40 系列:MPC83xx 处理器类型:32-位 MPC83xx PowerQUICC II Pro 特点:- 速度:267MHz 电压:0.95 V ~ 1.05 V 安装类型:表面贴装 封装/外壳:516-BBGA 裸露焊盘 供应商设备封装:516-PBGAPGE（27x27） 包装:托盘
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*