- 您现在的位置：买卖IC网 > PDF目录3788 > SPC5516EAMMG66 (Freescale Semiconductor)IC MCU 32BIT 1MB FLASH 208MAPBGA PDF资料下载
参数资料
| 型号： | SPC5516EAMMG66 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 28/54页 |
| 文件大小： | 0K |
| 描述： | IC MCU 32BIT 1MB FLASH 208MAPBGA |
| 标准包装： | 90 |
| 系列： | MPC55xx Qorivva |
| 核心处理器： | e200z1 |
| 芯体尺寸： | 32-位 |
| 速度： | 66MHz |
| 连通性： | CAN，EBI/EMI，I²C，SCI，SPI |
| 外围设备： | DMA，POR，PWM，WDT |
| 输入/输出数： | 144 |
| 程序存储器容量： | 1MB（1M x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 64K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 4.5 V ~ 5.25 V |
| 数据转换器： | A/D 40x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 208-BGA |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页
MPC5510 Microcontroller Family Data Sheet, Rev. 3
Electrical Characteristics
Freescale Semiconductor
34
2.10
eQADC Electrical Characteristics
Table 15. eQADC Conversion Specifications (Operating)
Num
Characteristic
Symbol
Min
Max
Unit
1
ADC Clock (ADCLK) Frequency1
1 Conversion characteristics vary with F
ADCLK rate. Reduced conversion accuracy occurs at maximum FADCLK rate. The
maximum value is based on 800KS/s and the minimum value is based on 20MHz oscillator clock frequency divided by a
maximum 16 factor.
FADCLK
112
MHz
2
Conversion Cycles
CC
14+2 (or 16)
14+128 (or 142)
ADCLK
cycles
3
Stop Mode Recovery Time2
2 The specified value is for the case when the 100nF capacitor is not connected to the REFBYPC pin. When the capacitor is
connected to the REFBPYC pin, the recovery time is 10ms.
TSR
20
—
μs
4
Resolution
—
1.25
—
mV
5
INL: 12 MHz ADC Clock3
3 At V
RH – VRL = 5.12 V, one lsb = 1.25 mV = one count.
INL12
—
10
Counts
6
DNL: 12 MHz ADC Clock3
DNL12
—
10
Counts
7
Offset Error with Calibration3
OFFWC
—
10
Counts
8
Full Scale Gain Error with Calibration
GAINWC
—
10
Counts
9
Disruptive Input Injection Current 4, 5, 6, 7
4 Below disruptive current conditions, the channel being stressed has conversion values of 0x3FF for analog inputs greater than
VRH and 0x000 for values less than VRL. This assumes that VRH ≤ VDDA and VRL ≥ VSSA due to the presence of the sample
amplifier. Other channels are not affected by non-disruptive conditions.
5 Exceeding limit may cause conversion error on stressed channels and on unstressed channels. Transitions within the limit do
not affect device reliability or cause permanent damage.
6 Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate
resistance values using VPOSCLAMP = VDDA + 0.5V and VNEGCLAMP = – 0.3 V, then use the larger of the calculated values.
7 Condition applies to two adjacent pads on the internal pad.
IINJ
—±1
mA
10
Incremental Error due to injection current. All channels have
same 10k
Ω < Rs <100kΩ 8
Channel under test has Rs=10k
Ω,
IINJ=IINJMAX,IINJMIN
8 At V
RH – VRL = 5.12 V, one lsb = 1.25 mV = one count. This count error is in addition to the TUE count error.
EINJ
—
±6
Counts
11
Total Unadjusted Error for single ended conversions with
calibration3, 9, 10, 11, 12
9 The TUE specification will always be better than the sum of the INL, DNL, offset, and gain errors due to canceling errors.
10 TUE includes all internal device error such as internal reference variation (75% Ref, 25% Ref)
11 Depending on the customer input impedance, the Analog Input Leakage current (DC Electrical specification) may affect the
actual TUE measured on analog channels shared digital pins.
12 It is possible to see up to one additional count added for the 144 pin packages since the VRL and VRH functions are shared
with the VSSA and VDDA, respectively. On Analog pins above PA15, the accuracy effects from adjacent digital port pin activity
is application dependent because of frequency, level, noise, etc.
TUE
—
±10
Counts
12
Source Impedance13
13 If R
S is greater than 1 k Ohm, be sure to calculate the affect of pin leakage and use the proper sampling time, to ensure that
you get the accuracy required.
RS
—
100k
Ohm
相关PDF资料 |
PDF描述 |
|---|---|
| MCF51JM64VLH | IC MCU 64KB FLASH 64LQFP |
| MCF51JM64VQH | IC MCU 64KB FLASH 64QFP |
| MC908AP8CFBE | IC MCU 8K FLASH 8MHZ 44QFP |
| S9S08DZ48F1MLC | IC MCU 8BIT 48KB FLASH 32LQFP |
| S9S08DN60F1MLF | IC MCU 8BIT 60KB FLASH 48LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SPC5516EAVMG80 | 制造商:Freescale Semiconductor 功能描述:MCU 32-bit MPC55xx e200 RISC 1536KB Flash 3.3V/5V 208-Pin MA-BGA Tray 制造商:Freescale Semiconductor 功能描述:1MB FLASH, 125C, 66MHZ, - Bulk 制造商:Freescale Semiconductor 功能描述:32-bit Microcontrollers - MCU 1MB FLASH, 125C 66MHZ 制造商:Freescale 功能描述:MCU 32-bit MPC55xx e200 RISC 1536KB Flash 3.3V/5V 208-Pin MA-BGA Tray |
| SPC5516EBMLQ66 | 功能描述:32位微控制器 - MCU AN15 FIXED RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT |
| SPC5516EBVLQ66R | 制造商:Freescale Semiconductor 功能描述:32-BIT MPC55XX RISC 1.5MB FLASH 3.3V/5V 144-PIN LQFP T/R - Tape and Reel |
| SPC5516GAMMG66 | 功能描述:32位微控制器 - MCU 1MB FLASH 125C 66MHZ RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT |
| SPC5516GBMLQ66 | 功能描述:32位微控制器 - MCU AN15 FIXED RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。