参数资料
| 型号： | SQE48T20050-PGB0 |
| 厂商： | Power-One |
| 文件页数： | 4/14页 |
| 文件大小： | 0K |
| 描述： | DC/DC EIGHTH BRICK |
| 标准包装： | 100 |
| 系列： | * |
SQE48T20050 DC-DC Converter Data Sheet
36-75 VDC Input; 5.0 VDC @ 20 A Output
Operations
Input and Output Impedance
These power converters have been designed to be
stable with no external capacitors when used in low
inductance input and output circuits.
In many applications, the inductance associated with
the distribution from the power source to the input of
the converter can affect the stability of the converter.
The addition of a 33 μF electrolytic capacitor with an
ESR < 1 Ω across the input helps ensure stability of
the converter. In many applications, the user has to
use decoupling capacitance at the load. The power
converter will exhibit stable operation with external
load capacitance up to 10,000 μF on 5.0 V output.
Additionally, see the EMC section of this data sheet
The device must be capable of sinking up to 0.2 mA
at a low level voltage of ≤ 0.8 V. An external voltage
source ( ± 20 V maximum) may be connected directly
to the ON/OFF input, in which case it must be
capable of sourcing or sinking up to 1 mA depending
on the signal polarity. See the Startup Information
section for system timing waveforms associated with
use of the ON/OFF pin.
Remote Sense (Pins 5 and 7)
The remote sense feature of the converter
compensates for voltage drops occurring between
the output pins of the converter and the load. The
SENSE(-) (Pin 5) and SENSE(+) (Pin 7) pins should
be connected at the load or at the point where
regulation is required (see Fig. B).
for discussion of other external components which
may be required for control of conducted emissions
Vin (+)
SQE48 Converter
(Top View)
Vout (+)
100
Rw
ON/OFF (Pin 2)
The ON/OFF pin is used to turn the power converter
on or off remotely via a system signal. There are two
remote control options available, positive and
Vin
ON/OFF
Vin (-)
SENSE (+)
TRIM
SENSE (-)
10
Vout (-)
Rw
Rload
negative logic. with both referenced to Vin(-). A
typical connection is shown in Fig. A.
Fig. B: Remote sense circuit configuration.
CAUTION
Vin (+)
SQE48 Converter
(Top View)
Vout (+)
SENSE (+)
If remote sensing is not utilized, the SENSE(-) pin must be
connected to the Vout(-) pin (Pin 4), and the SENSE(+) pin
Vin
ON/OFF
TRIM
Rload
must be connected to the Vout(+) pin (Pin 8) to ensure the
converter will regulate at the specified output voltage. If these
SENSE (-)
connections are not made, the converter will deliver an
CONTROL
INPUT
Vin (-)
Vout (-)
output voltage that is slightly higher than the specified data
sheet value.
Because the sense leads carry minimal current,
Fig. A: Circuit configuration for ON/OFF function.
The positive logic version turns on when the ON/OFF
pin is at a logic high and turns off when at a logic
low. The converter is on when the ON/OFF pin is left
open. See the Electrical Specifications for logic
high/low definitions.
The negative logic version turns on when the pin is
at a logic low and turns off when the pin is at a logic
high. The ON/OFF pin can be hard wired directly to
Vin(-) to enable automatic power up of the converter
without the need of an external control signal.
The ON/OFF pin is internally pulled up to 5 V
through a resistor. A properly de-bounced
mechanical switch, open-collector transistor, or FET
can be used to drive the input of the ON/OFF pin.
large traces on the end-user board are not required.
However, sense traces should be run side by side
and located close to a ground plane to minimize
system noise and ensure optimum performance.
The converter’s output overvoltage protection (OVP)
senses the voltage across Vout(+) and Vout(-), and
not across the sense lines, so the resistance (and
resulting voltage drop) between the output pins of
the converter and the load should be minimized to
prevent unwanted triggering of the OVP.
When utilizing the remote sense feature, care must
be taken not to exceed the maximum allowable
output power capability of the converter, which is
equal to the product of the nominal output voltage
and the allowable output current for the given
conditions.
JUL 07, 2006 revised to APR 12, 2007
Page 4 of 16
www.power-one.com
相关PDF资料 |
PDF描述 |
|---|---|
| OSTHI110050 | CONN TERM BLOCK 11POS 5MM |
| 74ACT245SJX | IC TRANSCVR TRI-ST 8BIT 20SOP |
| 74LCX2244WMX | IC BUFF DVR LOW V N-INV 20SOIC |
| OSTV8115151 | TERM BLOCK PLUG 5.08MM 11POS |
| MC74AC244DWR2G | IC BUFF/DVR TRI-ST DUAL 20SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SQE48T20050-PGB0G | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| SQE48T20120-NDA0G | 功能描述:DC/DC转换器 240W 12V at 20A Bus Converter RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| SQE48T20120-NDABG | 功能描述:DC/DC转换器 240W 13V at 20A baseplate RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| SQE48T20120-NDB0G | 制造商:Power-One 功能描述:- Bulk 制造商:Power-One 功能描述:Module DC-DC 1-OUT 12V 20A 5-Pin 1/8-Brick |
| SQE48T30012-NGB0 | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。