参数资料
| 型号： | SQE48T20050-PGB0 |
| 厂商： | Power-One |
| 文件页数： | 7/14页 |
| 文件大小： | 0K |
| 描述： | DC/DC EIGHTH BRICK |
| 标准包装： | 100 |
| 系列： | * |
SQE48T20050 DC-DC Converter Data Sheet
36-75 VDC Input; 5.0 VDC @ 20 A Output
All data presented were taken with the converter
soldered to a test board, specifically a 0.060” thick
printed wiring board (PWB) with four layers. The top
and bottom layers were not metalized. The two inner
layers, comprised of two-ounce copper, were used to
provide traces for connectivity to the converter.
The lack of metalization on the outer layers as well
as the limited thermal connection ensured that heat
transfer from the converter to the PWB was
minimized. This provides a worst-case but consistent
scenario for thermal derating purposes.
All measurements requiring airflow were made in the
vertical and horizontal wind tunnel using Infrared (IR)
thermography and thermocouples for thermometry.
Ensuring components on the converter do not
exceed their ratings is important to maintaining high
reliability. If one anticipates operating the converter
at or close to the maximum loads specified in the
derating curves, it is prudent to check actual
operating temperatures in the application.
Thermographic imaging is preferable; if this
capability is not available, then thermocouples may
be used. The use of AWG #40 gauge thermocouples
is recommended to ensure measurement accuracy.
Careful routing of the thermocouple leads will further
minimize measurement error. Refer to Fig. E for
optimum measuring thermocouple location.
Fig. E: Location of the thermocouple for thermal testing.
Thermal Derating
Load current vs. ambient temperature and airflow
rates are given in Fig. 1 and Fig. 2. Ambient
temperature was varied between 25 °C and 85 °C,
with airflow rates from 30 to 500 LFM (0.15 to
2.5 m/s), for vertical and horizontal converter
mounting.
For each set of conditions, the maximum load
current was defined as the lowest of:
(i) The output current at which any FET junction
temperature does not exceed a maximum
specified temperature (120 °C) as indicated by the
thermographic image, or
(ii) The temperature of the transformer does not
exceed 120 °C, or
(iii) The nominal rating of the converter (20 A).
During normal operation, derating curves with
maximum FET temperature less or equal to 120 °C
should not be exceeded. Temperature at the
thermocouple location shown in Fig. E should not
exceed 120 °C in order to operate inside the derating
curves.
Efficiency
Efficiency vs. load current plot is shown in Fig. 3 for
ambient temperature of 25 oC, airflow rate of
300 LFM (1.5 m/s), vertical converter mounting, and
input voltages of 36 V, 48 V, and 72 V. Also, a plot of
efficiency vs. load current, as a function of ambient
temperature with Vin = 48 V, airflow rate of 200 LFM
(1 m/s) with vertical mounting is shown in Fig. 4.
Power Dissipation
Fig. 5 shows the power dissipation vs. load current
plot for Ta = 25 oC, airflow rate of 300 LFM (1.5 m/s)
with vertical mounting and input voltages of 36 V,
48 V, and 72 V. Also, a plot of power dissipation vs.
load current, as a function of ambient temperature
with Vin = 48 V, airflow rate of 200 LFM (1m/s) with
vertical mounting is shown in Fig. 6.
Startup
Output voltage waveforms, during the turn-on
transient using the ON/OFF pin for full rated load
currents (resistive load) are shown without and with
external load capacitance in Fig. 7 and Fig. 8,
respectively.
Ripple and Noise
Fig. 11 shows the output voltage ripple waveform,
measured at full rated load current with a 10 μF
tantalum and 1 μF ceramic capacitor across the
output. Note that all output voltage waveforms are
measured across a 1 μF ceramic capacitor.
The input reflected ripple current waveforms are
obtained using the test setup shown in Fig. 12. The
corresponding waveforms are shown in Fig. 13 and
Fig. 14.
JUL 07, 2006 revised to APR 12, 2007
Page 7 of 16
www.power-one.com
相关PDF资料 |
PDF描述 |
|---|---|
| OSTHI110050 | CONN TERM BLOCK 11POS 5MM |
| 74ACT245SJX | IC TRANSCVR TRI-ST 8BIT 20SOP |
| 74LCX2244WMX | IC BUFF DVR LOW V N-INV 20SOIC |
| OSTV8115151 | TERM BLOCK PLUG 5.08MM 11POS |
| MC74AC244DWR2G | IC BUFF/DVR TRI-ST DUAL 20SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SQE48T20050-PGB0G | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| SQE48T20120-NDA0G | 功能描述:DC/DC转换器 240W 12V at 20A Bus Converter RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| SQE48T20120-NDABG | 功能描述:DC/DC转换器 240W 13V at 20A baseplate RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| SQE48T20120-NDB0G | 制造商:Power-One 功能描述:- Bulk 制造商:Power-One 功能描述:Module DC-DC 1-OUT 12V 20A 5-Pin 1/8-Brick |
| SQE48T30012-NGB0 | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。